Rane TTM56 Operator's Manual

Also see for TTM 56: Operator's manual Datasheet

Rane TTM56 Operator's Manual Manual pdf 1 page image

Manual-1TTM 56PERFORMANCEMIXEROPERATORS MANUALQuick StartCongratulations! You are the proud owner of an exceptionalperformance instrument. Experienced turntablists will find theTTM 56 comfortable and familiar. The TTM 56 has many uniquefeatures which are mastered quicker if you read the manual.Right! We know you can’t resist jumping right in, but please readat least this portion of the manual. It will help you get a goodstart.About the Faders: The Channel Faders and Crossfader aremagnetic, non-contact Faders. This means No travel noise – Nobleed – Ever! The electrical performance of the Faders is unaf-fected by use. Old habits are hard to break, but you really don’thave to mess with the Faders. The magnetic Faders in this mixerare very different from what you are used to. Be sure and read theQ and A section on page Manual-10.Special Features:• Channel Fader MODE switches allow selecting two sets ofcurves:MODE 1 gives the familiar stereo fader response.MODE 2 gives a left/right pan effect.• Both curves allow continuous adjustment of CONTOUR,giving smooth blend or fast cut.• The CHANNEL REVERSE switch allows the left-hand orright-hand Fader to control PGM 1 or PGM 2.• The CROSSFADER MODE switch allows selecting two setsof curves:WEAR PARTS: This product contains the following wear parts subject to the ninety (90) day warranty period described onpage Warranty-1: ST 2 Phono/Line Switch Assembly (2).MICLEVELHIGHLOWHIGH GAIN GAIN HIGHMID EQ EQ MID AUX OUTLOWFlexFX FlexFXLOW PHONES LEVELPGM 2PGM 1MASTEROL100+12-12+12-12+6OFF+6OFF+6OFF+6OFF+6OFF+6OFF100642 8642 8100642 8100642 8100642 8100642 8AUX IN+10+7+4+20-4-2-7-10-20100642 8PERFORMANCE MIXERFASTSLOWTTM 56LREVERSECONTOURREVERSEMODE 1MODE 2CONTOURMODE 1MODE 2CHANNEL REVERSETRANSFORM TRANSFORMSTEREO HOUSEMONO PGM1 / PGM2A BPAN R DRY WET L PAN MASTER / CUERPGM 1 CUE PGM 2REVERSE MODE 1 MODE 2FASTSLOWMODE 1 gives the familiar PGM 1 to PGM 2 cross-fade response.MODE 2 gives a center cut response (PGM 1 and PGM 2 are off in the center).• Independent CONTOUR controls for each side of the Crossfader allow cut on one side and blending on the other (or anycombination).• Auxiliary Inputs and Outputs, with independent level controls, give session mixing ability.AUX Inputs may be used for drum machine, tape, etc.AUX Input is after the Crossfader and after the Effects loop.AUX Outputs may be used for recording, booth monitoring, or a second zone.AUX Output is the same as the Master Mix.• FlexFX™ allow assignment of PGM 1, PGM 2 or both to the effects loop. The effects loop is post-fader. You get great resultswhen using the Channel Faders or Crossfader with reverb or other delay effects. WET/DRY pan lets you control how mucheffect is in the mix.• Three-band Accelerated-Slope™ EQ allows full cut of each band. The EQ engage switch lets you A/B compare or quicklytransform the EQ effect.• Two, 10-segment meters provide dual-mono-Cue or stereo-Master operation.• Yes, we included a power switch on the rear.The flexibility of the TTM 56 Faders can result in some initial confusion. We highly recommend trying one thing at a time.This helps avoid initial confusion. Make sure the Channel reverse switch is off. Start by changing the Mode and Contour of eachfader, one at a time. See the diagrams on pages Manual-6-7 to understand the fader responses under different settings. Once youunderstand the controls, start creating!