SAL SMF/BTAS/BP Quick Start Manual
  |
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.Nominal frequency (Hz) Product installation orientationOperating ambient min/max (°C) Product applicationOperating humidity Pixie connectivityStorage ambient limit (°C) *IP ratingStorage humidity Attachment typeHorizontal wall mount50*IP rating for interior products: The designated IP rating is “from below the ceiling” unless otherwise specified.IP rating ALL products: Termination of the product must be made in accordance with the IP rating.Model No. Input (V)/(Hz) Dimension L x W x H (mm)MUST BE INSTALLEDBY A LICENSEDELECTRICIANDIY0 to 40 Interior residential or commercial10% to 85% RH, NC0 to 60 20N/A10% to 85% RH, NCYesWirelessBluetooth Mesh TechnologySMF/BTAS/BP 240/50 N/A Blue 42 x 24 x 24SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474Copyright SAL V12 FEB 2020 | www.sal.net.au | Page 1 of 2PIXIE SMF/BTAS/BP MULTIFUNCTION CONTROL G3 electrical and installation specification effective 29/7/2020.SAL products are designed in accordance with all mandatory International and Australian Standards, which require installationin accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products aresold in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performanceguarantee unless expressly confirmed in writing by SAL at the time of order.General product application requirements (if applicable):1. CCT and POWER selections (where supplied) – IMPORTANT, where CCT colour temperature or POWER selection switching is provided, it is important to switch OFF thepower before the selection is made, otherwise equipment damage may occur.2. Recycling – SAL encourages recycling, please consider the environment when disposing of packaging, batteries & components.3. Switching or test intervals – For optimum product performance, good design practice does not encourage 24/7 operation of lighting products without the provisionof a routine switching or regulatory test cycle. As a guide for continual operation installations, a twelve (12) hour duration for Industrial and Commercial applicationsand a six (6) hour duration for Residential applications should be considered.4. Product maintenance – In line with the relevant design standards and to protect your investment, it is important to have in place a routine cleaning program thatreflects the installation environment and maintains the product in a clean and functional condition.IMPORTANT - The supply must be isolated before any product maintenance or cleaning is conducted. In addition, damage to ANY cable or cord supplied with theproduct must be addressed as follows; For attachment type X having a specially prepared cable, if the external flexible cable is damaged, it must be replaced by anequivalent cable exclusively available from the manufacturer or authorised installer. For attachment type Y, if the external flexible cable is damaged, it must beexclusively replaced by an equivalent cable by the manufacturer or authorised installer.For attachment type Z, if the external flexible cable is damaged, the cable cannot be replaced and the luminaire must be destroyed.5. Adverse, corrosive and coastal installation environments – Unless the product is specifically designated for such applications in these installation instructions, which issupported by a professional maintenance program; installation of equipment in such environments is not recommended.6. Dimming products – Dimming circuits and product compatibility must be validated by the installer before installation; SAL cannot be responsible for third partychanges in dimmer compatibility.7. Suspended products – For installation safety, any suspended products must NOT be installed in high air movement spaces or locations subject to impact.8. Light source replacements – (Non-replaceable light sources) - The light source of the product is deemed not replaceable, when the product reaches its end of lifethe complete product, it must be replaced by a qualified installer. (Non-user replaceable light sources) - The light source of the product must only be replaced by themanufacturer or qualified installer. Caution, risk of electric shock.9. Interior downlights and sensors with remote drivers and electrical accessories – The mounting facilities provided for the device (if any), need only be utilized if in theapplication of the product is required by AS/NZS3000. Drivers are not designed for installation environments that restrict conventional airflow.10. Floodlight products – Unless nominated aiming restrictions or installation parameters apply, products are designed for installation environments between ground and15 metres in height, subject to the desired optical performance being achieved.?11. Emergency enabled products – In the interest of transport and safety, emergency products are supplied with the battery disconnected. In addition to specificemergency commissioning instructions, this battery MUST be connected at the time of installation.12. Specific installation procedures (if any) - this device must be installed by a licensed electrician and is only compatible with SAL PIXIE Smart (master) devices:ColourMin / Max loadsOperation instruction: 1. Switch off the mains power2. Terminate conductors, as per the wiring diagram3. Switch on the mains power4. Program the product. One can either simply pair it with a PIXIE masterdevice to achieve multiway control, or program in PIXIE or PIXIE PLUS appcontrol a group or a scene. |
Related manuals for SAL SMF/BTAS/BP
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine