Safco 5117 Assembly Instructions Manual

Safco 5117 Assembly Instructions Manual Manual pdf 1 page image

5117-37MP: 1 of 6;Rev. 3: 12/03For questions or concerns, please call the Safco Consumer Hot Line 1-800-664-0042available Monday-Friday 8:00 AM to 4:30 PM (Central Time) (English-speaking operators)TOOLS REQUIRED: Standard ScrewdriverPRODUCT WARRANTY CARD is available online at: www.safcoproducts.comTASK MASTER ® INDUSTRIAL CHAIR(17” - 35” Range)A SA SA SA SA S S E M B LS E M B LS E M B LS E M B LS E M B L YYYYY I N S T R U C T I O N SI N S T R U C T I O N SI N S T R U C T I O N SI N S T R U C T I O N SI N S T R U C T I O N SNew Hope, MN 55428Visit us on the web:www.safcoproducts.coman LDI Company5117Check all parts against Parts List before beginning assembly.Allow all parts to warm to room temperature prior to assembly.Select either the LOWER or the HIGHER set of mounting holes on thelegs of the A Base. From the bottom, slide a B Lower Footrest (withthe curved front facing out) up between those legs until the holes inthe footrest line up with those in the legs. Place a C Footrest Nutinside the footrest, with the cupped side matching the curve of thefootrest end. Insert a D Flat Washer on to E Hex Bolt through thehole in the base leg and the footrest, and thread it into the footrest nut.Attach the other end of the footrest the same way. Now tighten boltsalernately with a wrench, until both sides are evenly tight. Do notovertighten.Install a F Glide onto each of the legs of the base. The glides shouldfit snugly, so place a glide under a leg and tap the leg into it with arubber mallet. Be sure the leg is inserted completely into the glide forproper stability. (HINT: Glides are easier to install if they are slightlyexpanded. Use a blow dryer or warm water, drying thoroughly, toexpand glides.)The G Tapered Bushing should come preassembled on HWavetube (contact Safco if it is not). Spread the tapered bushingslightly (it has a split side) and slide to about halfway down wavetube.Insert the wavetube assembly, wave surface first, into the central hubof the base; slide it down until the tapered bushing pops inside thehub and nests securely.Install the I Seat Assembly by aligning the hole on the undersidewith the shaft of the wavetube assembly; push down firmly on seat.Slide L Back Support Bar into bracket on underside of seat assem-bly. Use a standard screwdriver to depress push button near end ofBack Support Bar and slide Bar until push button locks into bracket.Remove K Knob with Cone Point from parts bag. Thread Knob intobracket and tighten to secure Back Support Bar in proper position.Make the final chair adjustments following the instructions on thereverse side.1 QQQQQ QQQQQQQQQQ2345QQQQQQQQQQ6QQQQQQQQQQQQQQQBase 1 5101-04Lower Footrest 1 5101-06Footrest Nut 2 5101-24Flat Washer 2 5147-31Hex Bolt 2 5101-23Glide 5 5101-25Tapered Bushing (on H) 1 5101-05Wavetube Assembly 1 5101-11Seat Assembly 1 5110-51Back Assembly 1 5110-52Knob with Cone Point 1 6680-78Back Support Bar 1 6680-55Knob with Flat Point 1 6680-77ABCDEFGHIJKLMQQQQQQQQQQQQQPART NO.PARTS LISTPARTS LISTPARTS LISTPARTS LISTPARTS LISTCODE DESCRIPTION QTY.QQQQQFQQQQQBQQQQQAQQQQQIQQQQQQQQQQKJRegistered U.S. Patents 5,836,555; D381,823QQQQQMQQQQQLQQQQQQQQQQQQQQQQQQQQHQQQQQGQQQQQCQQQQQDQQQQQEPARTS SHOWN IN BOXARE PRE-ASSEMBLED