SALSBURY INDUSTRIES1010 East 62nd Street, Los Angeles, CA 90001-1598Phone: 1-800-624-5269 Int’l Phone: 323-846-6700Fax: 1-800-624-5299 Int’l Fax: 323-846-6800www.mailboxes.com engineering@mailboxes.comInstallation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.Copyright © 2014 Salsbury Industries. All rights reserved. (Rev. 02, 2/19/14)Roadside Mailboxes – 43252-Wide and 3-Wide Spreader & Pedestal Installation InstructionsU.S.P.S. APPROVEDThank you for selecting Salsbury’s 4325 roadside mailbox. This instruction sheet is for installing 4325 mailboxes on a 2-wide or 3-wide spreader and a pedestal. Adifferent instruction sheet is available for installing 4325 mailboxes on a 4-wide spreader and a pedestal. Other installation instructions are available for installing themailbox on a pedestal, or on a deluxe mailbox post, installing the mailbox on a newspaper holder, and installing the pedestal in a concrete footing.When you install a curbside or roadside mailbox, make sure that it is easily accessible to the mail carrier. By regulation a locked mailbox should be 41” to 45” fromthe ground or street surface up to the point of mail entry. The door should be set back 6” to 8” back from the front face of the curb or the road edge. However, youshould check with your local postmaster to ensure that the mailbox is installed according to local regulations. It is important to note that it is not the responsibility ofmail carriers to open mailboxes that are locked, accept keys for this purpose, or lock mailboxes after delivery of the mail.Installing Mailboxes on Spreader & Pedestal4382 2-Wide SpreaderAll hardware to attach the spreader to the pedestal is included with thespreader. To attach the spreader to the pedestal, install four (4) 5/16”-18 X1” long hex flange head bolts through the four (4) center square holes of thespreader and through the four (4) tapped holes on the top plate of thestandard mailbox post. Cover the hex flange head bolts with cap plugs.All hardware to attach the mailboxes to the spreader is included with thespreader. To attach a mailbox, open the front door or rear door of themailbox and install four (4) 5/16”-18 x 1-3/4” long carriage bolts through thefour (4) square holes in the inside floor of the mailbox, through the squarespacer, and through the four (4) corresponding square holes in top of thespreader. Install 5/16” flat washers and 5/16”-18 hex nuts on the ends of thefour (4) bolts protruding below the bottom of the spreader. Repeat thesesteps for the other mailbox. Installation is now complete. Additionalhardware provided is not needed and may be discarded.4383 3-Wide SpreaderAll hardware to attach the spreader to the pedestal is included with thepedestal. To attach the spreader to the pedestal requires simultaneouslyattaching the center mailbox to the spreader and to the pedestal. Start byopening the front door or rear door of the center mailbox and install four (4)5/16”-18 X 2” long pan head bolts through the four (4) square holes in theinside floor of the center mailbox, through the square spacer, through thefour (4) center square holes of the spreader, and through the four (4) tappedholes on the top plate of the pedestal.All hardware to attach the remaining two mailboxes to the spreader isincluded with the spreader. To attach an additional mailbox, open the frontdoor or rear door of the mailbox and install four (4) 5/16”-18 x 1-3/4” longcarriage bolts through the four (4) square holes in the inside floor of themailbox, through the square spacer, and through the four correspondingsquare holes in top of the spreader. Install 5/16” flat washers and 5/16”-18hex nuts on the ends of the four (4) bolts protruding below the bottom of thespreader. Repeat these steps for the other mailbox. Installation is nowcomplete.