Salus EP110 Installer Manual And Quick Manual

Salus EP110 Installer Manual And Quick Manual Manual pdf 1 page image

Backlight/HolidayMode+1HrDownUpSelectSetResetInstaller Manual-Quick GuideAlways isolate the AC Mains supply before installing or working on any componentsthat require 230 VAC 50Hz supply.IntroductionA programmable controller is used to switch the heating system and/orthe hot water in your home on and off as needed. It works by controllingthe central heating and/or the hot water with programmed settings thattake effect at different times of the day.Go to www.salus-manuals.com for the full PDF version of the manual.Product ComplianceEU Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please checkwww.saluslegal.com for the full information.Safety InformationUse in accordance with the EU and national regulations.For indoor use only.Keep your device completely dry.This product must be installed by a competent person and in accordancewith all the EU and national regulations.Difference between EP110/EP210/EP310Installation Jumper SettingsFirst Power UpButton FunctionThe EP line will offer you the possibility to customize your central heating systemand hot water system as desired.EP110 is recommended for users that want to control only the Central Heating orthe Hot Water system.EP210 is designed to give you a full control with only one device of both yourCentral Heating and Hot Water system.EP310 is the most versatile product of this line and lets you manage two differentCentral Heating zones and the Hot Water with only one controller.Model: EP110/EP210/EP310Input: 230V, 50HzOutput: 3A/ switch terminal123EP110 Volt Free application onlyEP210 - 230V ApplicationEP310 - 230V ApplicationEP110 - 230V Application OnlyNote: Please remove red link wire for this application.Terminal Description BackplateN Mains NeutralL Mains Live1 Not Used2 Not Used3 Volt Free Connection4 Volt Free ConnectionEarth Parking(no electrical connection)N L 1 2 3 4 N L 1 2 3 4 5 6Terminal Description BackplateN Mains NeutralL Mains Live1 NC (Output)2 Not Used3 Switch Live (Output)4 230V Common (via Link)Earth Parking(no electrical connection)N L 1 2 3 4 N L 1 2 3 4 5 6Terminal Description BackplateN Mains NeutralL Mains Live1 Hot Water Off2 Central Heating Off3 Hot Water On4 Central Heating OnEarth Parking(no electrical connection)N L 1 2 3 4 N L 1 2 3 4 5 6Terminal Description BackplateN Mains NeutralL Mains Live1 Hot Water Off2 Central Heating Off3 Hot Water On4 Central Heating 1 On5 Central Heating 2 On6 Central Heating 2 OffEarth Parking(no electrical connection)N L 1 2 3 4 N L 1 2 3 4 5 6Changes to the jumpers settings should only be made by the Engineer carryingout the installation or other qualified person. The installer should select the jumperpositions required if changes need to be made to the factory default settings.These jumpers are found on the rear of the controller.* P - Fully pumped system for independent Central Heating and Hot Water.* G - Gravity Hot Water system with Pumped Central Heating.EP110/ EP210/ EP310 Switching BridgesSwitchProgram 5-2 days programme or24h programmeFully pumped system(P*)or gravity-fed hot watersystem(G*)Disable/enable the internalbackup batterySystemFeature EP110/310 SettingsMemoryBackup5-2 24H 24H5-2NA NA P GOFF ON OFF ONEP210 SettingsEP110/EP310 EP210EP110 EP310EP2101. Turn on the LCD backlight2. Press for 3 sec to activate Holiday modeSelect operating mode (ON, ONCE, AUTO, ADV, OFF)Activate/deactivate Boost functionDecreases the selected settingIncreases the selected settingSelect a clock or programme settingSets a clock or programme settingReset to Factory settingsEP110CH or HWEP210CH and HWEP3102x CH and 1x HWMODESELECTSET+HR

/ 2

Related manuals for Salus EP110