Synco P2T User Manual
Thank you for choosing SYNCO product.Please read this manual carefully before use and follow all instructions mentioned herein.Microphone P2T User ManualCaring For Your SYNCO ProductPackage ListProduct InstructionPlease keep the product in a dry, clean, dust-free environment.Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.Use only a soft and dry cloth for cleaning the product.Malfunction may be caused by dropping, impact of external force.Do not attempt to disassemble the product. Doing so voids warranty.Please have the product checked or repaired by authorized technicians if any malfunctions happened.Failure to follow all the instructions may result in mechanics damage.Warranty does not apply to human errors.TX Transmitter x2RX Receiver (Type-CConnector) x1 Wireless Charging Case x1Charging Cable x1Type-C to 3.5mm Adapter x1TX Transmitter RX Receiver Wireless Charging Case① Power② Working Indicators③ Built-in Mic④ Contacts⑤ Pocket Clip① Vocal Effects/ Mono/Stereo② Type-C Port③ Working Indicators④ Connector⑤ Contacts① Pairing/ Power Prompt② Type-C Port③ Working Indicators④ ContactsIndicator — Transmitter (Double press the Power button to turn off light effect)System unpairedCharging, and then turns off when fully chargeSystem paired, normal workingLow batteryFlash concurrentlySingle light keeps on (light effect off)Single light keeps on (in the case)Illuminate sequentially(light effect on)Single light flashesWorkingIndicators(WhiteLight)WorkingIndicators(Red Light)TX Transmitter RX Receiver Wireless Charging CaseIndicator — ReceiverIndicator — Wireless Charging CasePairingSystem unpairedStereo mode (Only original is supported)System pairedMono mode-Original soundMono mode-Vocal effects onIlluminate sequentiallyFlash concurrentlySingle light keeps on & Illuminate sequentiallySingle light keeps on & Illuminate sequentiallytwo-wayIlluminate sequentiallySingle light flashes twice & Illuminate sequentiallyWorkingIndicators(White Light)WorkingIndicators(WhiteLight)Operations1. Usage2. Pairing3. Charging① Tap on the right side of charging case to pop out the drawer② Take the TX and RX out③ TX should boot automatically as it leaved the case, and switch itself off automaticallywhen returning to the case.(Forcible switch: Long press the Power button on TX for 3 seconds)④ RX should boot automatically as it is plugged into smartphone① Place the TX and RX in the case with their contacts are connected with the case’s② Long press the Pairing button on the case for 3 seconds with the drawer open③ The indicators on the TX and RX should light up and illuminate sequentially whenpairing is successfulNote: The transmitter will automatically switch off if it is unpaired or disconnected for 5minutes.Charge the TX: Place the TX in the case with contacts connected with the case’s.Charge the case: Connect the case with power supply via the charging cable.Long press for 3 seconds4. Check the power5. Use vocal effectsTX: Short press the Power button, the indicators will light up according to remain powerfor 5 secondsCharging Case: Short press the Power Prompt button, the indicators will light upaccording to remain power for 5 secondsShort press the Vocal Effects button on the receiver to switch sound effects: Original >> Studio FX >> KTV FX >> VoiceAmplification >> EDM (Electronic Dance Music) >> Baby FX >> Male to Female >> Female to Male >> Monster FX.Default effect: Original.Note: The vocal effect will apply to both transmitters. In Stereo mode, only original is supported. Other vocal effects areunavailable.6. Mono/ StereoMono-OriginalMono-Other vocal effectsMono-OriginalLong press the Mono/Stereo button on the RX onceLong press the Mono/Stereo button on the RX onceLong press the Mono/Stereo button on the RX onceStereo |
Related manuals for Synco P2T
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine