System Sensor SPCW8 Installation And Maintenance Instructions Manual

System Sensor SPCW8 Installation And Maintenance Instructions Manual Manual pdf 1 page image

Ceiling Speaker: SPCW8 with listed enclosureIntended for use with separately sold tile support bracket: SB-SPC8PRODUCT SPECIFICATIONSStandard Operating Temperature: 32°F to 120°F (0°C to 49°C)Humidity Range: 10 to 93% Non-condensingNominal Voltage: 25 Volts or 70.7 VoltsMaximum Supervisory Voltage: 50 VDCSpeaker Frequency Range: 400 – 4000 Hz (Fire Alarm)200Hz – 15KHz (General Signaling)Power Settings: ⅛, ¼, ½,1,2, 4, 8 WattsInput terminal wire gauge: 12 to 18 AWG (2.5 mm²)MOUNTING BOX OPTIONSSPEAKERSSupplied EnclosureDIMENSIONS FOR PRODUCTS AND ACCESSORIESCeiling Speaker Diameter DepthSPCW8 Speaker with grill 12.8” 325.1mm 2.7” 68.6mmSPCW8 Speaker with back can 12.8” 325.1mm 4.2” 106.7mmTile Support Bracket Length Width Diameter openingSB-SPC8 23.75” 603.3mm 4.125” 104.8mm 10.75” 273.1mmNOTICE: This manual shall be left with the owner/user of this equipment.BEFORE INSTALLINGPlease read the System Sensor Voice EvacuationApplication Guide, which provides detailed in-formation on speaker notification devices, wiringand special applications. Copies of this manual areavailable from System Sensor. NFPA 72, CAN/ULCS524 and NEMA guidelines should be observed.Important: The notification appliance used must betested and maintained following NFPA 72 require-ments.GENERAL DESCRIPTIONSystem Sensor series of notification appliances offera wide range of audible and visible devices for lifesafety notification. The SPCW8 speaker is designedto be used at either 25 or 70.7 volts, with field se-lectable tap settings from ⅛ to 8 Watts. These prod-ucts are designed for high efficiency sound outputwith low total harmonic distortion to offer high fi-delity sound output.Its clear audibility is designed to meet life safetyneeds from fire to emergency communication mes-sages. With its wide frequency range it can alsobe used for general signaling such as paging andbackground music. The SPCW8 speaker is listedto ANSI/UL 1480, CAN/ULC S541 and CSA C22.2No. 205 requirements for public mode and generalsignaling applications as well as ANSI/UL 2043 ple-num rated. Speaker is suitable for indoor and dampinstallations.FIRE ALARM SYSTEM CONSIDERATIONSAll wiring must be installed in compliance with theNational Electrical Code (NEC , Canadian Electri-cal Code) and applicable local codes. System Sensorrecommends installing fire alarm speakers in com-pliance with NFPA 72, ANSI/UL 1480 , CAN/ULCS524 and NEC 760.WIRING AND MOUNTINGAll wiring must be installed in compliance with theNational Electric Code and the local codes as well asthe authority having jurisdiction. Wiring must notbe of such length or wire size which would causethe notification appliance to operate outside of itspublished specifications. Improper connections canprevent the system from alerting occupants in theevent of an emergency.Wire sizes up to 12 AWG (3.31 mm²) may be con-nected to the wiring terminals. The terminals arepre-set to accommodate 12 AWG wiring.I56-0005-000RINSTALLATION AND MAINTENANCE INSTRUCTIONS3825 Ohio Avenue, St. Charles, Illinois 60174800/736-7672, FAX: 630/377-6495www.systemsensor.comSPCW8 8 Inch Dual Voltage Speakerfor Fire and General Signaling Systems1 I56-0005-000R05-20

/ 4

Related manuals for System Sensor SPCW8