TAPKO MECip Operating Instructions Manual

Contents

product description

TAPKO MECip Operating Instructions Manual Manual pdf 1 page image

Operating Instructions MECipRelease version/date: R2.4 / March 2019© 2001-2019 TAPKO Technologies GmbHIm Gewerbepark A15, 93059 Regensburg, GermanyDetails, modifications and corrections may be subject to change without notice. TAPKO gives no warranty for the accuracy of the document. All rights reserved.Product description Connectors, buttons and LEDs descriptionThe MECip media coupler connects both media KNX IP and KNX TP.Used as KNX IP Router, it couples the KNX IP/Ethernet media to the TPbus system. KNXnet/IP routing and tunnelling are supported.MECip is able to filter the traffic according to the installation place inthe bus system hierarchy and according to the built-in filter tables forgroup oriented communication. Configuring from the subline can beblocked. For KNX devices, MECip provides commissioning, configuring,visualization, protocolling and diagnostic operation. Operational andfiltering states, malfunction and faulty communication are indicated byLEDs. Filtering can be temporarily deactivated by a single button press(eases commissioning because of short-time access to other lines).Extended frames and long messages with up to 240 bytes APDU lengthare supported. As UPnP is available, MECip is shown as network device.With a browser a comfortable front-end can be accessed to read outdevice settings, remotely activate functions (Progr. Mode, set tunneling)and watch a 30 min busload history diagram. Also, the integratedbootloader function enables remote firmware updates via IP/Ethernet.MECip is a rail-mounted device for installation in distribution boards on35 mm DIN rails. Supplied by the KNX bus line, the device does notrequire an additional power supply. KNX IP devices can be connectedby a standard RJ45 connector directly, and also via Ethernet networks.Requirements of Directives EMC, RoHS and LVD are met. Standards forresidential, commercial, and industrial environments are fulfilled. Thefull text of the EU declaration of conformity is available at the followinginternet address: www.tapko.de/ceState IP (Main line)green: Main line OKorange: Manual Function activeBus state KNX TP (Subline)green: Subline OKTelegram traffic IP (Main line)green (blinking):Telegram traffic extentred (blinking):Transmission errorTelegram traffic KNX TP (Subline)green (blinking):Telegram traffic extentred (blinking):Transmission errorGroup Address routinggreen: Filter activeorange: Route allred: Block all: Main line / subline differentEthernet connector Physical Address routinggreen: Filter activeorange: Route allred: Block all: Main line / subline differentFunction buttonProgramming button Programming LEDred: Programming Mode activered (blinking):No IP connectionKNX TP connectorTechnical specificationsPower inputPower supply:Current consumption:HousingDimensions (HxWxD):Mounting (IEC60715):Width in space units:KNX bus connection:IP connector:Weight:Environmental conditionsOperating temperature:Storage temperature:Ambient humidity:21…30 V DC SELV< 20 mA90 x 36 x 71 mm35 mm top-hat rail (TH35)2 modules at 18 mmKNX connector (red/black)Ethernet (RJ45, female)68 g-5…45 °C-20...60 °C5…93 % (non-condensing)Electrical safetyPollution degree (IEC60664):Protection type (IEC60529):Protection class (IEC61140):Overvoltage category (IEC60664):Approbation (ISO/IEC14543-3):CE MarkingEU Directives:Standards:2IP20IIIIIKNX-certifiedLVD (2014/35/EU)EMC (2014/30/EU)RoHS (2011/65/EU)EN50491-5-1/-2/-3EN50581EN60950-1EN61000-6-2/-3IEC60950-1Mounting, commissioning and safety notes Installation and maintenance After connection to the KNX bus system, the device works with itsdefault settings as intended Warning: Do not connect to 230 V. The device is supplied by theKNX bus and does not require any additional external power supply The device may only be installed and put into operation by aqualified electrician or authorized personnel For planning and construction of electric installations the appropriatespecifications, guidelines and regulations in force of the respectivecountry have to be complied For mounting use an appropriate equipment according to IEC60715 Installation on a 35 mm DIN rail (TH35) Connect the KNX bus line as for common KNX bus connections with aKNX bus cable, to be stripped and plugged into a KNX TP connector Do not damage electrical insulations during connecting Installation only in dry locations Accessibility of the device for operation and visual inspection must beprovided For changing the configuration use the ETS The housing must notbe opened Protect the device frommoisture, dirt anddamage The device needs nomaintenance If necessary, the devicecan be cleaned with adry cloth In the case of damage(at storage, transport)no repairs may becarried out byunauthorized personnel Configuration detailsand ETS database:www.tapko.de/mecip12345A6BC7D

/ 2

This manual is suitable for:

MECip

manualsdatabase

Your AI-powered manual search engine