TAPKO UIMtp Operating Instructions Manual
  | |
Contents | 
Operating Instructions UIMtpRelease version/date: R1.2 / March 2019© 2001-2019 TAPKO Technologies GmbHIm Gewerbepark A15, 93059 Regensburg, GermanyDetails, modifications and corrections may be subject to change without notice. TAPKO gives no warranty for the accuracy of the document. All rights reserved.Product description Connectors, buttons and LEDs descriptionThe KNX USB interface UIMtp provides a bi-directional connection tothe KNX TP bus system. PCs can be connected via USB. USB and bussystem are galvanically isolated. UIMtp is supplied by USB. No externalpower supply is necessary.With the possibility to address all bus devices, network configurationsbecome less time-consuming. For the devices connected to KNX, UIMtpprovides:CommissioningAddressingConfiguringVisualizationProtocolDiagnostic operationsUIMtp supports USB suspend mode. Communication protocol used forcommunication between interface and host is the flexible “cEMI”protocol. The connection between KNX and a PC with standard software(like ETS, EITT; also in Raw Frame operating mode) or other software ishandled by the Falcon driver. Extended Frames and long messages withup to 220 byte APDU length are supported.Requirements of Directives EMC, RoHS and LVD are met. Standards forresidential, commercial, and industrial environments are fulfilled. Thefull text of the EU declaration of conformity is available at the followinginternet address: www.tapko.de/ceUSB connectorKNX TP connectorState USBgreen: USB connection OK(blinking indicates telegram traffic)red: USB Suspend ModeBus state KNX TPgreen: KNX TP line OK(blinking indicates telegram traffic)Technical specificationsPower inputPower supply:Current consumption:HousingDimensions (HxWxD):Mounting (IEC60715):Width in space units:KNX bus connection:IP connector:Weight:Environmental conditionsOperating temperature:Storage temperature:Ambient humidity:21…30 V DC SELVUSB, 5 V DC< 5 mA (KNX TP)< 20 mA (USB)90 x 36 x 71 mm35 mm top-hat rail (TH35)2 modules at 18 mmKNX connector (red/black)USB2.0 (Type B, female)62 g-5…45 °C-20...60 °C5…93 % (non-condensing)Electrical safetyPollution degree (IEC60664):Protection type (IEC60529):Protection class (IEC61140):Overvoltage category (IEC60664):Approbation (ISO/IEC14543-3):CE MarkingEU Directives:Standards:2IP20IIIIIIKNX-certifiedLVD (2014/35/EU)EMC (2014/30/EU)RoHS (2011/65/EU)EN50491-5-1,EN50491-5-2,EN50491-5-3,EN50581,EN61000-6-2,EN61000-6-3Mounting, commissioning and safety notes Installation and maintenance After connection to the KNX bus system, the device works with itsdefault settings as intended Warning: Do not connect to 230 V. The device is supplied by USBand does not require any additional external power supply The device may only be installed and put into operation by aqualified electrician or authorized personnel For planning and construction of electric installations the appropriatespecifications, guidelines and regulations in force of the respectivecountry have to be complied For mounting use an appropriate equipment according to IEC60715 Installation on a 35 mm DIN rail (TH35) Connect the KNX bus line as for common KNX bus connections with aKNX bus cable, to be stripped and plugged into a KNX TP connector Do not damage electrical insulations during connecting Installation only in dry locations Accessibility of the device for operation and visual inspection must beprovided For changing the configuration use the ETS The housing must notbe opened Protect the device frommoisture, dirt anddamage The device needs nomaintenance If necessary, the devicecan be cleaned with adry cloth In the case of damage(at storage, transport)no repairs may becarried out byunauthorized personnel Configuration detailsand ETS database:www.tapko.de/uimtpAB12 |
Related manuals for TAPKO UIMtp
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine