Takex PXB-100SW Instruction Manual
Main FeaturesCoverage of light beamsDetection lineReceiverTransmitter(1) DOUBLE MODULATION(2) WIDE BEAM(3) QUAD HIGH POWER BEAM(4) LOW CURRENT CONSUMPTION(5) ECOLOGY(6) INSECT/WATER PREVENT(7) ANTI-BIRD SPIKE(8) DRIP-PROOF HOUSING(9) DUAL RING SIGHT(10 ) TARGET COLOR(11 ) INCREASED ANGLEADJUSTMENT ALLOWANCE( 13 ) WIRELESS ALIGNMENT CHECKER(12 ) SOLAR BATTERY CORRESPONDENCE( 14 ) LIGHTNING PROTECTIONKeeps birds and small animals away from thesensor, helping to reduce false alarms.Prevents rain and snow from streaming downthe front side of housing, helping to avoid falsealarm.The vivid color of the internal structure can berecognized easily from the far end in the beamalignment procedure.The color differs between a transmitter and areceiver which helps easy installation andchecking.Enables easy and accurate beam alignment.(Sold separately)Minimize the damage by the induced surgethrough wirings.It may stand 10000V under normal mode,15000V under common mode.It can be used with solar battery unit in a sitewithout a power supply. It becomes possible toinstall without wiring work.Vertically ±20˚ compared with previous version.It may adapt to the slope installation fl exibly.Enables better and clear view for easy beamalignment.This device is an opposed type photoelectric beam sensor that consists ofa photo transmitter that transmits infrared light, and a photo receiverfor the transmitted light, as shown in the illustration on the right.The infrared light transmitted from the transmitter expands in a coneshape, while the light beams enter the receiver.The straight line that connects the transmitter with the receiver is thedetection line.If the detection line is obstructed (light is obstructed for more than 0.05– 0.7 seconds), the receiver detects this break in the light beams, andoutputs a signal.The current consumption of this products is a little. so it can be usedwith solar battery unit in a site without a power supply.Even in case wired, the thin wire is enough for wiring due to lesscurrent consumption. It is good for moneywise.In order to ensure that the detection line has sufficient margin ofsensitivity, adjust the direction of the light beams before placing thesystem into operation. Providing sufficient margin of sensitivity reducesthe occurrence of malfunction caused by dense fog, heavy rain, frost,snow, and other such weather conditions.Double modulated beams are designed todistinguish the external lights.It increases the reliability in the outdoor securitysystem.The pitch between upper beam and lower one iswidened more than old models.False alarm by birds and falling leaves reducesdrastically.The beam power is 100 times of the minimumrequirement.The beam distance is 10 times of the describedspecification.This high power beam also realizes the reliabilityagainst the harsh conditions like fog, snow, heavyrain.50% less than remaining models. The battery sizemay reduce, wiring diameter may lessen,installation cost may decrease.RoHS adapted – Environment friendly. Free fromLead, Mercury, Cadmium, Hexavalent chromium,Polybrominated biphenyl, Polybrominateddiphenyl ether.Anti-insect bushing and special gasket enableIP65 rated tight housing.Instruction ManualLOW CURRENT PHOTOELECTRIC BEAM SENSORPXB-100SW: OUTDOOR 330ft (100m)Thank you for purchasing this product.Read this instruction manual before using the product to make sure that you use it correctly. |
Related manuals for Takex PXB-100SW
Takex PXB-100ATC-KH Instruction Manual
Takex MS-100E Instruction Manual
Takex PB-100AT-KH Instruction Manual
Takex PR-5B Instruction Manual
Takex MX-12FAM Instruction Manual
Takex PB-30SU Instruction Manual
Takex PA-6614E Instruction Manual
Takex MX-12FAMD Instruction Manual
Takex PB-IN-50HF Instruction Manual
Takex PA-5312E Instruction Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine