INSTALLATION INSTRUCTIONSMAKE CONNECTIONS TO WATER LINESUse 1/2” IPS faucet connections (1) and tighten connections with wrench. Or use the supplied plasticcoupling nuts (3) with 3/8” O.D. ball-nose risers (2), hand tighten only. Do not overtighten. Do not usemetal coupling nuts (4). Do not use plumber’s putty, pipe dope, or any other type of sealing com-pound on water inlet or threads. Additional compound is not necessary.INSTALO RSO UCIO WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.A BTURN OFFTURN OFF4SILICONETHIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT123 14THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLYENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.HAVE BASIC TOOLS READYRECOMMENDED TOOLS:1FlashlightTeflon tape Screwdrivers Adjustable andPipe wrench Plumber’s puttySafety gogglesTorque wrench Silicone caulk56EXPLODED DIAGRAM FOR REFERENCEMAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep itlooking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wooland harsh chemicals as these will dull the finish and void your warranty.HAND TIGHTEN THE WING NUTSFrom underneath the sink, hand tighten the wing nuts. Tighten gently until snug and alternate from sideto side to seat the faucet body evenly.Don’t over tightenFLUSHING & AERATOR CLEANINGRemove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucethandles all the way on and run water through the spout for about a minute to remove debris. Whilewater is running check all connections for leaks. Reassemble the aerator and screw it back into thespout hand tight.3 GASKET & FAUCET INSTALLATIONA) Apply a bead of plumber’s putty or silicone caulk around the sink openings.B) Install the gasket over the three holes in your sink.C) Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.Don’t use plumber’s putty on cultured marble or other composite sinks.Putty will discolour the sink.2 TURN OFF THE MAIN WATER SUPPLYLocate water supply inlets and shut off water supply valves. These are usually found underthe sink.WARNING: READ ALL the instructions completely before beginning.READ ALL warnings, care and maintenance information.Taymor recommends calling a professional if you are uncertain about installing this product!This product should be installed in accordance with all local and provincial plumbing and building codes.Need Help? Please call our toll-free Customer Support line at(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.C06-4481TWO HANDLE BAR FAUCETYour installation may require new supplylines. (Supply lines are not included.)71 - INDEX2 - SCREW3 - HANDLE4 - BONNET5 - WASHER6 - CARTRIDGE7 - SEAT8 - SPRING9 - ESCUTCHEON10 - BODY11 - BASE PLATE12 - MOUNTING NUT13 - COUPLING NUT14 - CLIP15 - O-RING16 - WEARABLE RING17 - NUT18 - SPOUT19 - AERATOR WASHER20 - AERATOR21 - AERATOR SHELL