heat exchangerapplication manualnx liquid-cooledfrequency converters

General

Control I/O

Parameter lists

Keypad control (Control keypad: Menu M3)

Description of parameters

Vacon NXP Manual

ENDAT/SSI, Sin-Cos Option Board OPT-BE

OPT-BE jumpers

OPT-BE LEDs

OPT-BE Parameters

Sin-Cos Option Board OPT-AK

OPT-AK jumper settings

OPT-AK parameters

Sin-Cos with Pulse Output Option Board OPT-AR

OPT-AR jumper settings

I/O terminals on OPT-AR, pulse output X3

Installation

Preface About this manual

Start-up Quick Guide

Approvals

Safety

Caution

Grounding and earth fault protection

Electro-magnetic compatibility (EMC)

Receiving the delivery

Type designation code

Storage

Accessories

FR7-FR8 cable accessories

Product modified" label

Mounting

Dimensions for wall mounting

Wall mounting of FR7

Wall mounting of FR8

Wall mounting of FR9

Dimensions for flange mounting

Flange mounting of FR7 and FR8

Flange mounting of FR9

Dimensions for standalone

Cooling

Cooling of standalone AC drives (FR10 to FR11)

Power cabling

UL standards on cabling

Cable and fuse sizes for 208-240 V and 380-500 V, FR4 to FR9

Cable and fuse sizes for 500-690 V, FR6 to FR9

Cable and fuse sizes for 380-500 V, FR10 to FR11

Cable and fuse sizes for 500-690 V, FR10 to FR11

Understanding the power unit topology

Brake resistor cables

Preparing for the cable installation

Frames FR8 to FR9

Frames FR10-FR11

Control unit

Control unit cabling

Installation of option boards

Galvanic isolation barriers

Control panel

Display

Navigation on the control panel

Using the Monitoring menu (M1)

Using the Parameter menu (M2)

Editing the text values

Editing the numerical values

Using the Keypad control menu (M3)

Changing the rotation direction

Using the Active faults menu (M4)

Using the Fault history menu (M5)

Resetting the Fault history menu

Changing the language

Comparing the parameters

Security

Keypad settings

Hardware settings

System info

Using the Expander board menu (M7)

Examining the connected expander boards

Finding the expander board parameters

Further keypad functions

Commissioning and additional instructions

Commissioning of the drive

The Run test without the motor

Measuring the cable and motor insulation

Frame FR7

Frames FR8 - FR11

Capacitor reforming

Technical data for NXS and NXP

Mains voltage 380-500 V

Mains voltage 500–690 V

Overload capability

Brake resistor ratings

The compliance with the product standard IEC/EN 61800-3 + A1

Environment definitions in product standard IEC/EN 61800-3 + A1

Fault tracing

Fault codes

Appendix 1 Power losses of 500-690 V

Introduction

Project specifications

Sections and options

Available sections

Main incoming section

Non-regenerative front-end section

Active front-end section

Inverter unit section

Drive sizes FI9-FI14

Dynamic brake section

Transport split unit

Cautions

Earthing and earth fault protection

Lifting and moving the sections

Fixing the sections

Fixing the cabinet to the floor or wall

Back-to-back installation

Connecting sections

Common busbars

Cabling

Control connections

Screw tightening torques

Service

Removing the drives from the cabinet

IUS_7 / IUS_8

IUS_9 / IUS_10

IUS_12

IUS_13 / IUS_14

Technical information

Pump and fan load

Technical specifications for VACON 5.3.1 NXN - Non-regenerative front end units

NXA - Active front-end units

NXI - Inverter units

NXB - Brake chopper units

Supplied documentation

Documentation examples

Parts list

Wiring list

Circuit diagram

Switchgear layout drawing

Device layout drawing

Requirements

Connection of signals between master and follower drive (OPT-A7)

Jumper setting on the OPT-A7 board

Terminal To Function" (TTF) programming principle

Defining a terminal for a certain function with NCDrive programming tool

Defining unused inputs/outputs

Shaft Synchronization Application – Parameter lists

Input signals

Output signals

Keypad control parameters

Application specific variables in the monitor menu and fieldbus interface

Shaft Synchronization operation

Shaft Synchronization fieldbus interface

Appendices

Parameters of motor thermal protection (ID's 704 to 708)

Shaft synchronization application specific fault codes

vacon

Available drive sizes

Enclosed solution sections

Incoming section

Drive section

DU/DT and internal cooler section

Heat exchanger section

Warnings

Lifting and moving the cabinets

Fixing the cabinets

Cooling pipe connections

Replacement instructions

Fuses

Cabinet fans for dU/dt and internal cooler

Internal cooler

Appenix

P&ID drawings


Contents Table Of Contents General Control I/O Parameter lists Keypad control (Control keypad: Menu M3) Description of parameters	heat exchangerapplication manualnx liquid-cooledfrequency converters Next / 54