Safety ManualVEGAFLEX 80 series4 … 20 mA/HART - two-wireWith SIL qualificationDocument ID: 42960

Instrument version

Planning 3.1 Safety function

Key figures acc. to IEC 61508

Setup 5.1 General information

Diagnostics and service 6.1 Behaviour in case of failure

Proof test 7.1 General information

Vega VEGAFLEX 80 Safety Manual

General instructions

Measuring range

Mounting, in general 2.1 Suitable housing versions

Installation on deck without protective cover

Mounting - standard 3.1 Actuating variables

Distance to vessel installations

Ways of fastening the probe

Mounting in a standpipe 4.1 Mounting - cable version

VEGAFLEX 81

operating instructions

Function

For your safety 2.1 Authorised personnel

NAMUR recommendations

Configuration

Principle of operation

Packaging, transport and storage

Mounting 4.1 General instructions

Mounting instructions

Connecting to power supply 5.1 Preparing the connection

Connection

Wiring plan, double chamber housing

Double chamber housing with DISADAPT

Supplementary electronics

Switch-on phase

Set up with the display and adjustment module 6.1 Insert display and adjustment module

Adjustment system

Parameter adjustment - Quick setup

Saving the parameter adjustment data

Setup with PACTware 7.1 Connect the PC

Parameter adjustment with PACTware

Set up with the quick setup

Set up with other systems 8.1 DD adjustment programs

Diagnostics and servicing 9.1 Maintenance

Status messages

Rectify faults

Exchanging the electronics module

Software update

Dismounting steps

Technical data

Dimensions

Industrial property rights

quick setup guide

Authorised personnel

Mounting 3.1 General instructions for use of the instrument

Connecting to power supply 4.1 Connecting

Wiring plan, single chamber housing

Set up with the display and adjustment module 5.1 Insert display and adjustment module

Supplement 6.1 Technical data

Information

Accessories and replacement parts

Connecting

Wiring plan, Ex-d-ia double chamber housing

Double chamber housing with VEGADIS-Adapter

Wiring plan - version IP 66/IP 68, 1 bar

Saving the parameterisation data

Maintenance

Exchanging the cable/rod

SIL qualification according to IEC 61508

Double chamber housing with DIS-ADAPT

Functional safety (SIL 6.1 Objective

Safety concept of the parameterization

Setup process

Set up with the display and adjustment module 7.1 Insert display and adjustment module

Parameter adjustment

Setup with PACTware 8.1 Connect the PC

Set up with other systems 9.1 DD adjustment programs

Diagnostics and service 10.1 Maintenance

ambient conditions

quick start

Product description 3.1 Configuration

Parameter adjustment - Extended adjustment

Diagnostics and service 9.1 Maintenance

How to proceed in case of repair

for your safety

product description

principle of operation

Connecting to power supply and bus system 5.1 Preparing the connection

Wiring plan

Set up with the indicating and adjustment module 6.1 Adjustment volume

Setting up sensor and Modbus interface with PACTware 7.1 Connect the PC

software update

technical data

Basics Modbus

Modbus register

Modbus RTU commands

Levelmaster commands

error codes

Configuration of typical Modbus hosts

Set up the sensor with the display and adjustment module 6.1 Adjustment volume

Diagnostics and service 8.1 Maintenance

Dismounting 9.1 Dismounting steps

symbols used

EU conformity

Mounting

Connecting to power supply

Set up with the display and adjustment module

Setup with PACTware

Set up with other systems

Diagnostics and servicing

Dismount

Communication Profibus PA

general instructions

Shortening the coax probe

Maintenance and fault rectification 5.1 Maintenance

Dismount 6.1 Dismounting steps

About this document

For your safety

Product description

Supplement

Connecting to power supply and bus system

Set up the sensor with the display and adjustment module

Setting up sensor and Modbus interface with PACTware

Set instrument address

How to proceed if a repair is necessary

VEGAFLEX 82

vegaflex 83

VEGAFLEX 86

VEGAFLEX 80


Contents Table Of Contents Instrument version Planning 3.1 Safety function Key figures acc. to IEC 61508 Setup 5.1 General information Diagnostics and service 6.1 Behaviour in case of failure Proof test 7.1 General information	Safety ManualVEGAFLEX 80 series4 … 20 mA/HART - two-wireWith SIL qualificationDocument ID: 42960 Next / 20