Wahl Lithium-Ion 9860L Operating Instructions Manual

Also see for Lithium-Ion 9854L: User manual

Wahl Lithium-Ion 9860L Operating Instructions Manual Manual pdf 1 page image

432 5 6 7149 108 1311 12head are even.3 For the top of the head, cut with the grain using the individual guidecomb attachments. The smaller the number of the comb, the shorter thecut. Comb or brush the hair as you cut for an even end result.4 To complete the fade, blend the hair at the fade line by trimming upand out across the line and against the grain all the way around thehead. Then, repeat all around, turning the trimmer upside down andcutting downward. The final objective is to blend the hair so there isno real line, just a perfect fade from bald to very short hair. You canachieve this by using the #1 individual guide comb attachment. Continuecombing and cutting until you achieve the desired effect.5 To create a part, pick a spot off-center. Pull the scalp tight and with theend of the blade perpendicular to the head, move the trimmer back andforth to cut a line. Comb through it and cut again to make sure the cutis precise.TRIMMING PRIVATE AREAS with the trimmer &detailer head.1. Volume reduction using trimmer head. Attach guide comb and select along trimming length. Begin trimming, starting at the top and workingdown. Use progressively closer settings to get the “look” and length youprefer.2. For hard to reach or tight areas, use the detailer head. Always pull skintaut. Then slowly move the detailer through area to trim until desired lookis accomplished.3. Shave in your private areas by gently shaving in the desired area andalways keep the skin taut.TRIMMING NoSE HAIR using detailer head.Make sure the nasal passages are clean. Slowly move the detailer in andout of each nostril, no more than 1/4-inch deep.TRIMMING EAR HAIR using detailer head.Make sure the outer areas of the ears do not contain any wax. Hold the earflat with one hand and carefully insert detailer no more than 1/4-inch intothe outer ear.CAUTIoN: Do not insert the detailer or any other foreign object intothe inner ear. For hair growing on the outside of the ear, simply move thedetailer slowly along the edges of the ear.TRIMMING EyEbRowS using detailer head.Slowly move detailer to neatly trim stray hairs. For precise, even trimming,slowly move the detailer closer or farther away from eyebrows to achievedesired length. Do not press against brow as it may remove too much hair.FADE CUT using a T-blade1 Start at the temple and cut all the way around the head to establishthe ultimate location of the fade line. Always cut against the grain for theshortest cut. Don’t force the blade through the hair. Let the trimmer dothe work.2 Next, cut around the head again and up the nape of the neck to thefade line, brushing away the cut hair as you go. Pull the scalp taut withthe thumb for the closest cut. Turn the trimmer upside down whennecessary to keep cutting against the grain. Make sure both sides of theears and hairline.4. Accentuate your beard line by using thetrimmer in a downward motion. Startat the line you’ve created and, workingfrom the chin back toward the ears,trim the area right under your beard line.5. Define the upper part of your beardusing the same technique.6. For a neater finished look, replaceattachment blade to the detail bladeforward. Use this blade for fine, detailtrimming anywhere it is needed, suchas at the sideburns near the ears,goatees, etc.DETAILING NECKLINES, SIDEbURNS, MUSTACHES& bEARDS using trimmer head.Slowly move trimmer downward on desired areas to neatly trim and shape.TRIMMING ARM & LEG HAIR using trimmer head.Simply glide the trimmer over your arm or leg until desired hair length isachieved. The first time you trim the hair, start by using a longer setting onthe guide comb on the trimmer, then use progressively shorter settings if ashorter length is preferred.TRIMMING CHEST & SToMACH using trimmerhead.Glide the trimmer over your torso region, in an upward motion until desiredhair length is achieved. For tight, scratch-free trimming, use the #1 guidecomb.FoR THE CLoSEST LooK, after trimming, attach the shaverhead. The shaver makes for the perfect tool to groom the total body. Usingthe same technique, as mentioned prior, youcan groom wherever you feel a need. Shaveagainst hair growth while stretching the skin.After every use, remove the shaver foil bypressing both side buttons and carefully usingcleaning brush provided. Self-sharpening blades are high compression, high-carbonsteel, made to maintain their shape and sharpness for extendedperiods.TRIMMING AND EDGING yoUR bEARDThe following are suggested trimming steps and trimmer positions.You may find different procedures workbetter for you.1. Comb your beard in the direction thatit grows to help reveal stray hairs thatmay be longer than the others.2. Attach the 6-position trimming guideto trim and taper your beard. Beginwith the guide set at a long trimming length. Trim towardyour chin in smooth, overlapping strokes, following the lay ofyour beard. If you trim against the wayyour beard naturally lays, the trimmerwill cut the hair much shorter and theresult may be patchy.Adjust the trimming guide toprogressively shorter settings until you reach the desired lengthof beard. You may wish to set the trimming guide attachmentto cut closer near the ear and down under the chin, changingto a longer setting toward the front of the face and point of yourchin. When the trimming guide is removed, it will remain at its lastlength setting until you change it.Always be sure the trimming guide is locked solidly into thedesired position before you start totrim.3. To cut the outline of your beard,remove the trimming guide. Startingunder your chin and working backtoward your jawbone and ears, cutthe outer perimeter of your beardunderneath the jawbone. Continue the line all the way up to theCARING FoR yoUR TRIMMERoILING bLADESFor best results, put one or two drops of Wahl Clipper Oil onthe blades only when necessary, or approximately once a month.Motor bearings are permanently lubricated—do not attempt to oil.When oiling your trimmer, turn the trimmer “ON - I,” hold the unitwith the blades facing DOWN and squeeze one or two drops of oilonto the blades. Wipe off excess oil with soft cloth.NoTICE—Do NoT oVER oIL!Excessive oiling or application of liquids will cause damage ifallowed to seep back into motor.bLADE CARETrimmer blades have precision-hardened, ground and lappedcutting teeth. Blades should be handled carefully and neverbumped or used to cut dirty or abrasive material. Never rinse theblades with water, or the blades may rust. Clean with the includedbrush.CLEANING/SToRAGEBefore storing your trimmer, use the cleaning brush to whiskany loose hairs from the unit and the blades. For units with asoft-touch grip, use a damp cloth to wipe down the body of thetrimmer, taking care not to get the blades wet.Store unit in such a manner so that bladesare protected from damage.When the trimmer is not in use, thetrimmer guide/blade guard attachmentshould be in place to protect the blades.This appliance should be stored in amanner where it is not subjected toCrushing, Heating above 100°C (212°F),or Incineration.IMPoRTANT SAFEGUARDSWhen using your electrical appliance, basicprecautions should always be followed,including the following:READ ALL INSTRUCTIoNS AND SAFEGUARDSbEFoRE USING THIS TRIMMER.DANGERTo reduce the risk of death or injury byelectric shock:1. Do not reach for an appliance that hasfallen into water. Unplug immediately fromthe outlet.2. Do not use while bathing or in a shower.3. Do not place or store appliance where itcan fall or be pulled into a tub or sink. Donot place in or drop into water or otherliquid.4. Except when charging, always unplugthis appliance from the electrical outletimmediately after using.5. Always unplug this appliance beforecleaning.6. (Rechargeable unit only.) Unplug thecharger before using trimmer.TRoUbLESHooTINGIf your Trimmer does not seem to take a charge, check the followingbefore returning it for repair:1. Check outlet to make sure it is working by plugging in anotherappliance.2. Make sure the outlet simply is not connected to a light switch whichturns the power at the outlet off when lights are turned off.3. Be sure the trimmer is properly connected to the rechargingtransformer, all connections are secure and the switch on thetrimmer is turned “OFF - 0.”4. If your electricity is connected to a master power switch, wesuggest the trimmer be disconnected from the charger anytimethe master switch is off. Leaving the unit plugged into a deadoutlet or an unplugged charger will drain the battery.5. If trimmer does not run and it is completely charged, turn the unit“ON - I” and pinch or push the blades manually. (Oil may have driedout between the blades, so they may be temporarily stuck together.)LITHIUM-IoN bATTERyREPLACEMENT, CLIPPERDISPoSAL AND RECyCLING:• For battery replacement send the entire, intact clipper unit to: WahlAnnex 3001 North Locust, P.O. Box 578, Sterling, IL 61081• Do not attempt to remove the battery. Lithium-Ion batteries canexplode, catch fire, and/or cause burns if disassembled, damaged, orexposed to water or high temperatures.• If you choose not to replace the battery, the entire, intact clipper unitmust be disposed. Do not attempt to remove the battery for disposal.Lithium-Ion batteries may be subject to local disposal regulations.Many locations prohibit disposal in standard waste receptacles.Check your local laws and regulations.• For recycling contact a government recycling agency, wastedisposal service, retailer, or visit online recycling sources, such aswww.batteryrecycling.com or www.rbrc.org.where oxygen is being administered.9. Never drop or insert any object into anyopening.10. Do not use this appliance with a damagedor broken blade or trimming attachment, asfacial injury may occur.11. Always attach plug to appliance first, thento outlet.To disconnect, turn unit “oFF - 0,”then remove plug from outlet.SAVE THESE INSTRUCTIoNSFor Household Use onlyRECHARGING1. This trimmer is conveniently designed for household use. Itshould be allowed to charge 1 hour before first use.2. Remove the trimmer, recharging transformer and accessoriesfrom the packing material.3. Connect the transformer to the trimmer. BE SURE TRIMMER ISIN THE “OFF - 0” POSITION WHEN CHARGING.4. Plug the recharging transformer into any convenient electricaloutlet at the correct voltage.5. When trimmer is low in power, it should be connected to thetransformer and plugged into an outlet to assure maximumpower is available when it is next used. This transformeris designed to completely charge the battery withoutovercharging. Do not use the trimmer while it is charging.6. The battery will take approximately 60 minutes to charge. TheLithium Ion Trimmer also has quick charge capability.7. Insert only recharging transformer plug supplied by themanufacturer into charger receptacle.wARNINGTo reduce the risk of burns, electrical shockor injury to persons:1. Do Not Crush, Disassemble, Heat Above100°C (212°F), or Incinerate the appliance,due to Risk of Fire, Explosion, or Burns.2. This power unit is intended to be correctlyorientated in a vertical or floor mount position.3. Close supervision is necessary when thisappliance is used by, on, or near children ordisabled persons.4. Use this appliance only for its intendeduse as described in this manual. Do notuse attachments not recommended by themanufacturer.5. Never operate this appliance if it has adamaged cord or plug, if it is not workingproperly, if it has been dropped or damaged,or if it has been dropped into water. Returnthe appliance to Wahl Clipper Corporation forexamination and repair.6. Keep the cord away from heated surfaces.7. Only insert approved transformer plug ortravel plug into charger receptacle.8. Do not use outdoors or operate whereaerosol (spray) products are being used orLithium•Ionthe release tab down to secure in position. To remove the guide,gently push up on the release tab and slide the assembly awayfrom the trimmer. Adjust the trimming length by pressing on thethumb lever and moving the comb forward or backward to thedesired setting. A Detachable blade system enables you to quickly changefrom a standard-width blade for full grooming to a narrow-width blade for detail trimming around a mustache, goatee, oranywhere to define the hair lineand clip any stray whiskers.To remove attachment, simply pulltop edge of blade away from bodyunit. To attach, align back tab of attachment head to cavity on theinner edge of trimmer unit and push down on top of blade.Should blades become damaged or dull or if you want additionalattachment heads for your trimmer, you may purchase themfrom Wahl. Be sure to ask for the following attachment with partnumber from our service and repair department (see last page forcontact information):Attachment Head:Wahl Part NumberTrimmer: #59300Detailer: #59301T-Blade: #59302Shaver: #59303Rotary: #59306www.wahltrimmers.comThe trimmer you purchased may not have all of these heads, butthey will all work with your trimmer if you wish to purchase them.SPECIAL FEATURES:Your trimmer has been designed with several advanced featuresto help you get perfect results every time you trim. Your trimmermay be used to neatly trim goatees, beards, mustaches, neckline,sideburns around the ears and eyebrows, or anywhere you mayneed grooming. It also makes a great all-around family trimmer formini haircuts and touch ups between trips to the barber or to cleanup the shape of the neck. Soft-Touch Grip (9854L, 9860L) allows you to hold thetrimmer in a comfortable position for precision trimming. An Ergonomic Shape and gripping horizontal bars (9876L)for added comfort, designed so you always hold the trimmer ina comfortable position for precision trimming.The shape also provides optimum trimmingvisibility. A Rotating Head (9876L). The trimminghead rotates 360 degrees, providing twotrimming positions. This allows you to achievethe optimum ergonomic relationship betweenthe hand, the trimmer and the face. Rotate thehead to the desired position as follows. Withthe switch in the “OFF - 0” position, depressthe lock button and rotate the head clockwise orcounterclockwise 360 degrees. A 6-Position Trimming Guide makesachieving a consistent trim easy every time.The guide can be removed (providing aseventh cutting position) and reattachedwithout changing the preset cutting length,so once you have found the perfect length,there’s no guesswork in achieving it every trim.The trimming guide is a two-piece assembly,consisting of a base and a comb. It shouldnot be disassembled. To attach the guide,simply slide it on at a slight angle and pressoperating Instructions for theLithium Ion Grooming KitsInstrucciones de operaciónde la recortadora recargable#1 Stubble Length (2 mm)#2 Short (4 mm)#3 Medium Short (6 mm)#4 Medium (8 mm)#5 Medium Long (10 mm)#6 Long (12 mm)TRIMMING wITH ATTACHMENT CoMbSYour Trimmer includes three trimming attachments; stubble, mediumand long. The stubble guide has 1 bar, the medium-cut attachment hastwo bars and the long-cut attachment has threebars. These attachments are ideal for blending,tapering and defining beards, as well as forachieving a “close trim” stubble look around theface. To use the attachments, go with the hairdirection. To achieve closer looks, go againstthe hair direction.Detachable Blade TrimmerRecortadora con láminasdesmontable9876L9854L9860LSERVICE AND REPAIRIf you have problems with your trimmer, send it prepaidwith a note explaining the problem to:Wahl Clipper CorporationAttn: Repair Department3001 Locust StreetSterling, IL 61081Telephone (800) 767-9245For products purchased outside the United States, contact your distributor.If for any reason within 30 days of purchase of your Wahl®trimmer you are not satisfied with your trimmer and wouldlike a refund, just return your trimmer, together with the salesreceipt, to the retailer from whom you purchased it. Wahl willreimburse all retailers who accept trimmers within 30 days ofpurchase. If you have any questions regarding this money-back guarantee, please call 1-800-767-9245 in the UnitedStates.30 Day Money back Guarantee!#59300 #59301 #59302 #59306#593039854L9876L 9860L1 2 3© 2011 Wahl Clipper CorporationPart No. 91668Printed in U.S.A.For more information or Product Registration, visit www.wahltrimmers.com5-yEAR LIMITED wARRANTyValid in U.S.A. onlyIf your Wahl product fails to operate satisfactorily within five(5) years from the date of original purchase or receipt as a gift,Wahl will, at our option, repair or replace it and return it to youFREE OF CHARGE. Do not return this product to store wherepurchased. Products needing repair under this warranty shouldbe returned with postage prepaid to:wahl Clipper Corp.Attn: Repair Department3001 Locust StreetSterling, Illinois 61081Include a note describing the defect and the date of originalpurchase or receipt as a gift (if in warranty). Products out ofwarranty will be repaired at our standard repair charges.This warranty is void and no repair or replacement will be madeunder this warranty or otherwise if: (1) The product is modifiedin any manner or repaired by anyone other than Wahl ClipperCorporation or Wahl authorized service center. (2) The producthas been used commercially or subjected to unreasonable use.This warranty gives you specific legal rights and you mayalso have other rights which may vary from state to state. Noother written express warranty is given. Any implied warranty,including any warranty of merchantability which may arise frompurchase or use, is limited to the year period provided in thisexpress warranty. Some states may not allow such limitation,so it may not apply to you. No responsibility is assumed forincidental or consequential damages of any type, or for the useof unauthorized attachments. Some states may not allow theexclusion or limitation of incidental or consequential damages, sothe limitation or exclusion may not apply to you. Outside U.S.A.,check with store for Wahl authorized distributor’s warranty.www.wahltrimmers.com

/ 2

Related manuals for Wahl Lithium-Ion 9854L