Waterdrop WD-A1 Quick Installation Manual
Also see for WD-A1: Manual
 |
Product Information 3. User Interface (Water Dispensing Interface) b.Ke InstructionsWaterdropReverse OsmosisHot Cold Water Dispenser45.Quick Installation GuidePlease refer to Instruction Manual for details.2. Installing the FilterBody cover plateCFROStep 1: Takeout filters from package and remove the wrappingStep 2: Align the markson the filter and dispenser as shown, then insert the filter into the designatedbucket,Step 3: Gently pressand rotate the filter handle clockwise until it ocks in a horizontal position with a"icon. And make sure the" "icons on the filter and dispenser arealigned.2. Adding Water to the TankMaxWaste WaterFeed water tankStep 1: Removethe water tank cover plate, and pick up the water tank in an upward direction.Step 2: Fill the feed water tank with tap water.Step 3: Placethe water tank back into the dispenser, and cover it with the plate.Step 4.• Pushdown on the water tank to secureit in place.O NOTE:The largecompartment isthe feed watertank for tap water,while the smallone isthe wastewater tank forconcentrated water(unsuitablefor drinking). Pleasedo not addtap waterto the wastewatertankWhen adding water,ensure it doesnot exceedthe maximum water markto prevent overflow.1. SpecificationsProduct modelDimensionsOuter water tank volumeInner water tank volumeRated voltageRated frequencyRated powerHeating powerRefrigeration powerFeed water requirementWater temperature requirementDaily production rateTDS requirement for feed waterWD-AI1.06 Gal feed water tank +048 Gal waste water tank0.2 Gal purified water tank+026 Gal cold water tank110-120V/AC1,600WgowMunicipal tap water41-100 'F/5-38 •C100 GPDTDS<500Waterd ropCold Water IndicatorFilter Life IndicatorChild Lock Indicator : * o o41 FCup Volume Indicator—. 8 oz 32Status Indicator LightCup Volume KeyChild Lock Key.Night Mode IndicatorWater Filtering IndicatorWater Change IndicatorRight KeyTDS Level IndicatorWater Dispensing Key/Confirm KeyTemperature KeyCold Water KeyNOTE: The images in the manual,including the dispenser,accessories,and user interface,arefor referenceonly andmay not reflectthe exact appearance Asthe product issubject ta updatesand improvements,slight differencesmay existbetween the actualproduct and the images shown.Pleasereferto the actual product for accurate information.a.lndicator InstructionsO' NOTE:DonotusethisdispenserwithmicrobiologicallyunsafewaterorwaterofunknownqualityifthereisinsuffcieIndicator0JoIcon>StatusFlashesStays onOffFlashesStays onOffFlashesStays onOffonOnOffFlashesStays onOffFlashesOffKey & FunctionsChild lock:Pressthis key for a second to disable the child Ockand dispense hot water with atemperature of1130For above. Pressand hold this key for 5 seconds to cancel the child lock. Pressand hold it foranother 5 seconds to recover it.Cup volume key:Tap the key on the water dispensing interface to choose the desired water volume, such as oz,BOZ, 16 OZ, 20 OZ,or MAX.Tap the keywhile on the menu interface to quickly go back tothe water dispensing interface.Water Dispensing Key/Confirm KeyTap this key while in standby mode to activate the dispenser.To dispense water, tap this key on the water dispensing interface.To confirm the selected settings, tap this key in the menu settings interface.Temperature Key:Tap this key whi e on the water dispensing interface to choose the desired watertemperature, such as cold water, ambient water, 1130F,1400F,1850k or 2030KTapthis keyoncewhileon the menu interfaceto quicklygo backto the waterdispensinginterface.Cold water key:You can quickly accessthe cold water dispensing mode by tapping this key from the waterdispensing interface or menu interface.Pressand hold this key for 5 seconds to cancel cooling.Press and hold it for another 5 seconds to recover it.Left key:Tap this key on the water dispensing interface to check notifications, filter ife,operatinginstructions, and more.On the menu interface or notifications interface, tap this key to switch between available options.Right key:Tap this key on the water dispensing interface to check function settings.Tapthis keyon the menu interfaceor notificationsinterfaceto switch betweenavailableoptions,Quick Start Guidedisinfection before or after use,2. Main PartsBody cover plateDisplay screenWater outletDrip tray3. Flushing the New DispenserWater tank cover plateWater tankCF filterxl RO filterxl BrushxlHeat dissipating portsDispenser StatusPlease unlock it before dispensing hot water.The child lock ison. Please disable the child lock to dispense hot water.Thechild lockis off,or unlockingis not requiredbecausehot water is notdispensed in this modeThe filter isnear expiration.The filter has expired.The filter is in normal use,Water cooling is in progress.Cold water isavailable for dispensing.Cold water is unavailable for dispensing.The night mode is on, but the water cooling and filtering functions stillrun since it is not the designated hour.The dispenser iscurrently in night mode. This limits the water coolingand filtering functions.The night mode is off.The purified water tank is ow on water, and dispenser iswaiting to filter waterThe dispenser isfiltering water.There is sufficient water, and the dispenser can dispense water as expectedThe feed water tank is 0M,'on water, or the waste water tank isfull. Pleaserefill the feed water tank or discard the waste water promptly.The dispenser isfunctioning normally, and there isno need to change waterDaily Usageuse.water container larger than 08 Gal on the drip tray, and pressany key to start flushing.It is necessaryto perform a flushing process on a new dispenser before normal30 minutes and 3-4 tanks of water (about 3.2 Gal) in total.Step 1: When the dispenser isturned on for the first time, tap the confirm key"disp ays asshown.• After adding enough water to the feed water tank, tap the confirm key"step 2.Flushing takes about"until the interface"once.Then place a1. Water DispensingoStep 1: Tapthe" "icon to activate the interface while the dispenser is in the screen-off state.Step 2: Placea container or cup on the drip tray, the dispenser will automatical y detect it, and theinterface will light up.Step 3: Tapthe cup volumekey"6 "to selectthedesiredwatervolume:4Oz,8 Oz,16 Oz,20 Ozor MAX(continuous dispensing until the inner water tank is empty)This dispenser has an inbuilt compressor cooling system. Maintain a space of 20 cm/8 in on bothsides Ofthe dispenser for efficient heat dissipation.The cooling function will not be active for the first two hours after switching on the dispenser. Thisis necessary to protect the compressor.The dispenser's cooling function will turn on by default after two hours Of the initial power-on. Youcan press and hold the cold water key for five seconds on the water dispensing interface to turn Offthe function, and you can turn it on using the same method.When the cooling function is turned on, the dispenser's compressor operates intermittently toensure energy efficiency and a consistent cold water supply. Please note that it is normal for thecompressor to make a sound during its operation.a. About the water tem erature•To selecta temperature of 11-YFor higher, pressand hold the child Ockkey" "for 1 second to disablethe child lock,and then tap the water dispensing key"• Tapthecold waterkey"* "toquicklyaccesstheco d water.Selectthedesiredvolume,placeaocontainer, and tap the dispensing key" "to start. Pauseby tapping any key during dispensing.. About th tatu indicat r Ii htThe color of the status indicator light wil vary based on the water temperature:Waterdrop< System flushing? >WaterdrOPPlace acontainer, andpress any keyto start.Co d water-Blue,140'F-Orange,O: NOTE:Ambient water-White,185'F-Darkorange,1130F-Lightorange,203'F Reda 3Step 3: The dispenser will automatical y ter and dispense water during flushing. Tapping any key onthe interface will pausethe process.To resume, tap the confirm key"WaterdropFlushingPress any keyto pauseWaterdropContinueflushingWaterdrop140Waterdrop140Due to the heating power limitations and the temperature Ofthe feed water, increasingthe desireddispensedwatertemperature will resultin a lower flow rateThetemperature of the feed watertank directly impacts the dispensingtemperature of room temp waterand theflow rate Of hot water,2. Additional FunctionsRoutine Flushing: Pleasereferto Page7 of the Instruction Manual for details.Filter Resetting: Pleasereferto Page8 of the Instruction Manual for details.Night Mode: Pleaserefer to Page9 of the Instruction Manual for detailsOff-home Mode: Pleaserefer to Page9 of the Instruction Manual for details.Time Setting: Pleaserefer to page 10 Ofthe Instruction Manual for details,Boiling Point Correction: Pleaserefer to Page 10 of the Instruction Manual for details.NOTE: indicates ongoing flushing, wh ilea completion,Step4:Whentheindicator"(b ightsup,andtheinterfaceshowsasindicated,itmeansthedispenseris due for a water change. Pease empty the concentrated water, refill the feed water tank with tap water,and return the tank into the dispenserStep 5: Flushing is complete, and the new dispenser is ready for regular usewhen the interface displaysStep4:Tapthetemperaturekey"& "toselectthedesiredwatertemperature:cod water(106 122'F/41-50'C), ambient water (real-time temp), 113'F/45'C, 14ffF/60'C, 185'F/85'C or 203'F/95'C,Waterdrop113Step 5: Tapthe water dispensing key"BWaterdrop140eas shown.6WaterdropFeed watertank lack ofwaterWaterdropWaste watertank fullWaterdrop69e 160Z TDS20"to get your water, and tap any keyto pause it.Manufacturer Technical SupportTel: 1-888-352-3558 (US.)E-mail: service@waterdropfilter.com24/7SenioMade in China VOOIQingdao Ecopure Filter Ltd.NOTE: Waterdischarg«dduring theflushingprocessisnot drinkable |
Related manuals for Waterdrop WD-A1
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine