XM OnyX Quick Start Manual
1 24 536 7A. Be sure the vehicle is outside and the antenna has a clear view of the sky.B. Verify that you are receiving the XM signal. The radio should be tuned to channel 1, the XM Preview channel. Thereshould at least be one bar on the lower left corner of the screen that denotes antenna signal strength.C. You can also press menu and then press to scroll to and highlight Signal Indicator. Press the Select button. TheSatellite and Terrestrial bars show the strength of the signal being received. If the signal reception is good, pressand hold menu to return to channel 1, the XM Preview channel.Verify Signal ReceptionSignal IndicatorSATELLITETERRESTRIAL800-643-2112siriusxm.com1 XM PreviewFind a Location for OnyX and Mount itDash Mount Method:IMPORTANT: The air temperature needs to be at least 60û F to install the Dash Mount. If needed, turn on the heaterin your vehicle.A. Select a flat surface for the Dash Mount with ample room for OnyX. Avoid mounting on leathersurfaces.B. Orient the adhesive foot so that OnyX is easily accessible. Loosen the knob and adjust the adhesivefoot to position 1 or 2, and then tighten it.C. Clean the surface with the alcohol preparation pad.D. Once the surface is dry, remove the adhesive liner. Pressand hold the Dash Mount in place for 30 seconds. Allow theadhesive cure for 2-4 hours.E. You can tilt the dock mounting plate in your preferreddirection.TIP: Choose a location that doesn’t interfere with the driver’s vision or access to driving controls, won’t interfere withthe deployment of airbags or other safety equipment, and makes OnyX easily accessible for operation.jumpFMmenu2 3 4 5 6 7 8 9 0direct112 3 4 5 6 7 8 9 0directjump FMmenu122 3 4 5 6 7 8 9 0directjumpFMmenu11Dock Mounting Plate1 2Knob Adhesive FootVent Mount Method:A. Select a vent with ample room for OnyX.B. Some vents have recessed louvers. If yours are recessed, remove the regular vent clamps and install theextended vent clamps.C. Install the Vent Mount onto the vehicle vent:i. Insert the vent mount into the vent opening.ii. Push until hooked on the rear of the vent louver. Restthe foot against the bottom of the vent.iii. If necessary, adjust the tilt of the Vent Mount byrepositioning the foot to a different tilt adjustment hole.PUSHDashVentLouverFootVentVentDashDashHOOKEDTILTADJUSTMENTHOLES2 3 4 5 6 7 8 9 0directjumpFMmenu1jumpFMmenu2 3 4 5 6 7 8 9 0direct1Select either the Dash Mount method or the Vent Mount method for your OnyX. Do not attach the PowerConnect Vehicle Dock to the mount. Wait until after you have connected all the cables to the dock. A. Mount the Magnetic Mount Antenna outside your vehicle, on a clean and dry horizontal surface thatwill always face the sky.B. Choose the location for the antenna according to your type of vehicle. Center it between the left andright sides, and away from other antennas.C. Install the Cable Routing Adapter to direct the antennacable downward, if mounting on an edge.TIP: Use the Alcohol Prep Pad to clean the surface.Sedans and Coupes(above front windshield or rear window)Pickups(above front windshield)SUVs(rear of roof)Convertibles(leading edge of trunk)Route the Antenna CableNOTE: These instructions are for a sedan or coupe where the antennais mounted above the front windshield. The User Guide has detailedantenna cable routing instructions for all types of vehicles, beginningon page 26.A. Tuck the antenna cable under the windshield rubber moldingand run it to the nearest corner.B. Route the cable out of the molding and into the rubber weatherstripping around the door opening.C. Lift the weather stripping. Tuck and run the cable inside it tothe bottom of the door opening. Replace the weather stripping.D. Pull the cable out and route it to OnyX .E. Plug the Magnetic Mount Antenna connector into the silver ANT connector at therear the PowerConnect Vehicle Dock.TIP: Include enough slack in your routing to accommodate open doors or the hood lid. Coilany excess cable in a hidden location and keep it away from any vehicle pedals or controls.OnyXLocationAUDIO ANT PWR FMA. Insert the PowerConnect Power Adapter into your vehicle’scigarette lighter or power adapter socket. Plug the other end intothe red PWR connector on the rear of the PowerConnect VehicleDock.B. Use the wire guide on the top of the dock to organize the wiresconnected to the dock.C. Place OnyX into the dock and press the Power button.IMPORTANT! Don’t attach the dock to the mount just yet.Wire Guide2 3 4 5 6 7 8 9 0directjumpFMmenu1AUDIO ANT PWR FMMount the Magnetic Mount AntennaConnect the PowerConnect Power AdapterStart Here |
Related manuals for XM OnyX
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine