XPR Access WS4-4D-E Quick User Manual
Also see for WS4-4D-E: Quick user guide
  |
www.xprgroup.com 1ENWS44DE 4 Door access control unit with web accessDESCRIPTIONSPECIFICATIONSFACTORY RESETCHANGE PASSWORDSOFTWARE SETTINGSMETHOD 1ADDING READERSMETHOD 2ADDING USERSADDING SLAVE CONTROLLERSFIRST CONNECTION AND CONFIGURATIONIf you can not connect, it is because your network does not recognize the name of theWS44DE controller. In this case, go to our web site http://www.xprgroup.com/products/ws4/and download the tool called “Device Finder”.The “Device Finder” will enable you to ind out the IP address of the WS44DE controller.Run the “Device Finder” and you will get a list of all the WS4 controllers connected inyour network, including their IP addresses, just like the picture below.To add 2 readers on 1 Door, select the reader (ig.2) and there, for “Type of Access”select “Access with 2 readers” (ig 5). Fill the form for both readers and they willmerge in one door (ig. 6)WS4 system can manage up to 10 WS4 boards in the same installation (with up to 20doors, whether single or double). One WS44DE must be master, the others must beslaves. The master/slave selection is made with Dip-switch 2: OFF - Master (factorysetting), ON - Slave.Go to “Doors” and click on the link “Add slave”(ig.1). Enter the serial number of theWS44DE to be added and click Search. If it inds it, the system directly adds this slaveinto the installation and you can conigure its doors (ig.2).In case of error, a message is displayed in red.Go to Users (ig.1), select “New”(ig.2) and then ill the form (Name, category, cardnumber...)(ig.3).Open a browser and type the IP of the WS44DE controller and you will be prompted to thelogin page.User Name: adminPassword: WS4 followed by Dash and the Serial Number (ex. WS4110034) just like theimage below, all in capital letters without space.QUICK USER GUIDE• Capacity: 2500 Users• Events: 50000 max.• Doors: 4 (max. 20 doors in same network)• Readers: 4• Door contact inputs: 4• Push button inputs: 4• Auxiliary Inputs: 2 (emergency, vehicle detection)• Auxiliary Outputs: 2 (alarm, storing alarm status, presence)• Power supply: 120 to 240 V AC, 100 VA1.52A with fuse (1 A)• Supply for the readers: 225 mA each max.• Supply for the locks: 600 mA each max.• Relay characteristics: 2A/48 VAC/DC#• Processor: ARM A5 - 528 Mhz• Memory: 64 MB Ram DDR2 133 Mhz• TCP/IP connection: 10/100/1000 Base-T – HTTP or HTTPS• Dimensions (mm): 116 x 195 x 33 mm• Operating temperature: 0 °C to +50 °C• Humidity: 0% to 85% (non-condensing)• Tamper: Yes• Wiegand readers connection: Yes, via Wiegand to RS485 converter - WS4CNV• Elevator feature: Yes, 2 elevators per installation, each - 24 loors• Interlock, Anti pass back, people counter, presence, system logs, reports in CSVThe WS44DE does not have default IP address. By default is set to DHCP. There are 2methods to connect to and conigure WS44DE - LAN and Standalone method.In this coniguration, the network’s DHCP server will assign an IP address to your WS44DIn this coniguration, the WS44DE will assign an IP address to your PC. The PC must be set to obtain IPaddress automatically.(For use in a home or business LAN network)(For standalone use - without LAN network)1. Put the DIP switch 1 in position OFF.2. Connect a cable from your network to the ethernet connector of WS44DE.3. Open a web browser and enter http://ws4 followed dash and the serial number ofthe WS44DE controller1. Put the DIP switch 1 in position ON.2. Connect a cable from your PC directly to the ethernet connector of WS44DE.3. Open a web browser and enter the following IP - 192.168.50.100, then put the logincredentials like explained aboveDIP Switch 4 allows a complete re-initialization of the system. Todo this, switch this dip switch 3 times OFF - ON - OFF within 10seconds.DIP Switch 4 allows to log into the system as an administrator iflogin or password is forgotten. Toggle this dip switch ON forabout 15 seconds, then back to OFF. The system will then allow,for 5 minutes, to connect (from the local network only) with thedefault login and password.Go to “Doors”, select the reader(ig.2) and then select the type of the reader in theield ”Card”. (ig.3). While off line, red LED blinks fast and buzzer beeps continuously.Once communication is established, the red LED and the buzzer stop. Green LEDstarts to blink continuously. If you want to stop the green LED, go to Settings/SystemOptions and select for the backlight ON or OFF (not default) ig.4v.a2ig.1ig.3ig.5ig.1ig.2SwitchMaster/SlaveMasterDIP switch 2OFFSlave 1DIP switch 2ONSlave 9DIP switch 2ONig.3ig.6ig.4ig.2ig.1ig.2WS44DE is a 4 door control unit designed to operate with readers with RS485 output.There is no need to install any software. There is no need to have a dedicated PCeither. Everything is available online and the operators just need to register withcontroller’s serial number to start using the software application.NLDEESITFREN |
Related manuals for XPR Access WS4-4D-E
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine