Yaesu FT2DR Quick Manual

Also see for FT2DE: Operating manual Manual Operating instructions Operating manual Technical supplement

Yaesu FT2DR Quick Manual Manual pdf 1 page image

FT2DR/DEQuick Guide C4FM/FM1 Antenna (SMA)2 TX/BUSY LED3 Touch panel display4 [PTT] switch5 [MONI/T-CALL] switch6 [SQL] switch7 Power switch8 [DISP] key9 [BACK] key10 [X] key11 [GM] key12 Battery pack13 GPS antenna14 DIAL15 VOL16 microSD card slot17 DATA terminal18 MIC/SP terminal19 [BAND] key20 EXT DC IN terminal21 [V/M] key22 [A/B] keyInput / Edit the Call SignInput the Call SignWhen the power is turnedon for the first time afterpurchase, or when ALLR E S E T i s e x e c u t e d , ascreen to input the call signis displayed.P r e s s t h e k e y t odisplay the alphabet inputscreen. Use the keypadentry screen to input theCall Sign ID.Touch [123] to switch tothe numeric input screen.Touch [ABC] in the numericinput screen to return tothe alphabet input screen.Press to complete theCall Sign entry.Changing the Call SignThe Call Sign ID can bec h a n g e d u s i n g t h e s e tmode. Press the keyfor one second or longert o d i s p l a y t h e “ S E T U PMENU” and then touch[CALLSIGN].Alphabet input screen isdisplayed.Input the call sign using thealphabet input screen andthe numeric input screenand then press .EH060M551Return to the Current Operating ScreenTo exit set mode and return to the current operation mode,either press on the left side of the transceiver, or brieflypress the key repeatedly.Reset the SettingsReset AllPress the key for one second or longer while pressing thekey, key and key to turn the power ON.Touch [OK] when “ALL RESET?” appears on the display.Reset the Settings of the Set ModePress the key for one second or longer while pressingthe key and key to turn the power ON. Touch[OK] when “SET MODE RESET?” appears on the display.Select the Operating BandThe operating band is switched each time thekey is pressed. Also, in dual band operations, touchingthe frequency display area of the non-operating band(displayed in grey), will change it to the operating band.The frequency band displayed in black is the operatingband.Each time the key is pressed for one second orlonger, the screen will switch between dual band displayand mono band display.Adjusting the VolumeTurn the VOL knob to the left or right to adjust the volumeup or down.Selecting the Frequency BandSelect the frequency band by pressing the key.Touch [FMW] before pressing the key to switch thefrequency band in the reverse order.Press the [BAND] key to switch the receive frequencyoperating bands in the order shown in the below table.Touch [FMW] before pressing the [BAND] key, to switchthe bands in the reverse order.The receive frequency bands for Band A and B are asshown in the following table.Frequency Band (Band) Band A Band B522 kHz to 1710 kHz (AM radio band) ● —76 (88) MHz to 108 MHz(FM radio band) ● —1.8 MHz to 30 MHz(shortwave band) ● —30 MHz to 76 (88) MHz(50 MHz band) ● —108 MHz to 137 MHz(aeronautical radio band) ● ●137 MHz to 174 MHz(144 MHz band) ● ●174 MHz to 222 MHz ● ●222 MHz to 420 MHz(information radio band (1)) ● ●420 MHz to 470 MHz(430 MHz band) ● ●470 MHz to 774 (800) MHz*Band B is up to 580 MHz ● ●803 (800) MHz to 999 MHz(information radio band (2)) ● —( ):EXP/European VersionSetting the FrequencyPress the key to switch to the VFO mode and then turnthe DIAL. Or touch the frequency display area to show thekeypad entry screen and enter the frequency manually.Selecting the Communication ModeUse the radio in the AMS mode ( / / ) for normaloperations. The communications mode is automaticallyselected to match the mode of the received signals. Touch[MODE] to switch the communication mode.“AMS” → “DN (V/D mode)” → “VW (FR mode)” → “FM(Analog)”DN: Digital voice and data will be sent simultaneouslywith automatic error correction, for reliablecommunications.VW: Digital voice data is transmitted using the entire 12.5kHz bandwidth. High quality voice communication ispossible.FM: Analog communication using the FM mode.Changing the Transmit PowerTouch [FMW] and [TXPWR] and then turn the DIAL toselect the transmit output level.“HIGH” → “LOW1” → “LOW2” → “LOW3”(When a lithium-ion battery pack, or an external powersupply is connected)Press after selecting the transmit output power.Locking the Keys and SwitchesPress (power switch) to lock the key buttons. Press(power switch) again to release the lock.12345678910111213141516171819202122

/ 2

Related manuals for Yaesu FT2DE