Yaesu FTM-300DE Information For Customers Operating

Also see for FTM-300DE: Instruction manual Instruction manual Operating manual Advance manual Instruction manual

Yaesu FTM-300DE Information For Customers Operating Manual pdf 1 page image

1. Turn the transceiver ON.2. Press the [BAND(SQL)] key to enter the 144 MHz band.3. Press and hold the [MHz(SETUP)] key.4. Rotate the DIAL knob to select “OPEN MSG 28” andthen press the [MHz(SETUP)] key.5. Rotate the DIAL knob to select “MESSAGE” and thenpress the [V/M(MW)] key.6. Enter “AH075M”.1) Rotate the DIAL knob to select “A”, then press the [V/M(MW)] key.2) Repeat the previous step to complete the MESSAGE“AH075M”.3) Press and hold the [MHz(SETUP)] key.Information for Customers Operating VHF/UHF Transceivers in the UKThank you very much for purchasing the YAESU transceiver.The transceivers listed in this notice are configured at the factory with the ARS (Automatic Repeater Shift) FrequencyRange, and the Repeater shifts, as shown in the below chart “ARS Configuration B2”.When any of the listed transceivers is operated in a location where the frequency range and repeater shifts in use areas shown in the chart “ARS Configuration C2”; follow the respective procedure to change the Automatic RepeaterShift configuration, before using the transceiver for the first time.ARS Configuration “B2”Factory Default SettingARS Configuration “C2”Selectable SettingARS Frequency Range: 438.20 MHz - less than 439.45 MHz (- shift)Repeater Shifts: 7.6 MHzARS Frequency Range: 433.00 MHz - less than 433.40 MHz (+ shift)434.60 MHz - less than 435.00 MHz (- shift)Repeater Shifts: 1.6 MHzCaution:• By changing the ARS designated bands and repeater shifts according to the procedures below, all saved data, such asMenu and Memory settings, will be deleted. If you need to change the ARS feature setting after using the radio, makesure to back up your registered data or make a written note, before applying the setting change.• The ARS feature setting is NOT changed, even when executing the “Factory Reset” to restore the transceiver to thefactory defaults, as described in the Operating Manuals.7. Turn the transceiver OFF.8. Press and hold the [BAND(SQL)], [GM(AMS)] and[MODE(DG-ID)] keys while turning the transceiver ON.9. appears in the display.10. Rotate the DIAL knob to select and pressthe [GM(AMS)] key. The transceiver will re-start auto-matically. Setting of theARS feature to “Config-uration C2” is success-fully completed.To restore the ARS feature setting to the factory default (B2),perform the same procedures above.FTM-7250DEFTM-300DE1. Turn the transceiver OFF.2. Connect the supplied microphone SSM-85D to the trans-ceiver.3. Press and hold the [F(SETUP)] and [GM] keys while turn-ing the transceiver ON.4. Press the [Power] key briefly, then “LOCK” will appear onthe display for one sec.5. Press [8] à [9] à [7] à [7] à [3] à [5] keys on the SSM-85D microphone.6. appears in the display.7. Press the [Power] key briefly, then “UN LOCK” will ap-pear on the display for one sec.8. Rotate the DIAL knob to se-lect and pressand hold the DIAL knob. Theradio will re-start automatical-ly. Setting of the ARS featureto “Configuration C2” is suc-cessfully completed.To restore the ARS feature setting to the factory default (B2),perform the same procedures above.FTM-400XDE1. Turn the transceiver OFF.2. Connect the supplied microphone MH-48A6JA to thetransceiver.3. Press and hold the [F(MW)] and [GM] keys while turningthe transceiver ON.4. Press the [Power] key briefly, then “LOCK” will appear onthe display for one sec.5. Press [8] à [3] à [7] à [8] à [3] à [7] keys on the MH-48A6JA microphone.6. Press the [Power] key briefly, then “UNLOCK” will appearon the display for one sec.7. Press and hold the [DISP(SETUP)] key.8. Touch the [RESET/CLONE] on the display.9. T h e A R S C o n f i g u r a t i o nname “B2” will appear in thetop right of the display.10. Press [F(MW)] key, then themessage “B2” TO “C2”> will appear onthe display. BACKBACKRESET/CLONEFACTORY RESETPRESETRECALL PRESETMEM CH RESET〉〉〉〉VERSIONMAIN : x . x x x 0EXP B2PANEL: x . x x11. Touch [OK?]. The radio will re-start automatically. Set-ting of the ARS feature to “Configuration C2” is success-fully completed.To restore the ARS feature setting to the factory default (B2),perform the same procedures above.

/ 2

Related manuals for Yaesu FTM-300DE