YaliTech RTR505B User Manual

YaliTech RTR505B User Manual Manual pdf 1 page image

AreaBattery InstallationRecording starts automatically by inserting the battery with the defaultor previous settings.Thank you for purchasing our product.To ensure safe and proper operation, please read this guide thor-oughly before use.OverviewRTR505B is a data logger designed to measure and recorddifferent items depending on the input module to be con-nected: temperature (Thermocouple, Pt), analog signal(4-20mA, DC voltage), and pulse.Recorded data is then automatically collected by the Base Unit viawireless communication and downloaded for archive and analysis.BatteryCoverScrewRubberPackingDefault SettingsRecording Mode EndlessRecording Interval 10 minutesRecording StartMethodImmediate Start• Make sure to use the proper type andsize screwdriver. (Phillips head #1screwdriver is recommended.)• Insert the supplied battery with thetube attached. When using a CR2 lithi-um battery, the tube is not necessary.• Before closing the cover, check the rub-ber packing for dust or scratches, asthey can reduce the water resistance ofthe rubber.• Be sure to completely close the cover.Make sure not to over tighten thescrews.• Appropriate Tightening Torque:Lithium Battery 20N·cm to 30N·cm (2Kgf·cm to 3Kgf·cm)Wireless Data Recorder RTR505B is referred to as the “(data) logger” or“device” in this manual.tandd.com© Copyright T&D Corporation. All rights reserved.2021.11 16508210006 (2nd Edition) Printed on recycled paper.Package Contents• RTR505B or RTR505BL (Large Battery Type)• Lithium Battery LS14250 (or Large Capacity Battery Kit RTR-500B1 for L type model)• Strap (Not included with L type model)• Manual Set (Warranty Included)Part NamesAntennaLCD DisplayOCopmticmalunicationModule JackBattery ReplacementWhen it is time for the battery to bereplaced, a battery warning mark will ap-pear. Please change the battery as soonas possible if this mark appears.If you continue to use the logger without changing the battery, thecurrent temperature and [bAtt] will be displayed alternately and wirelesscommunication will stop. (Recording will continue.)AlternatingDisplay• If the battery is further left unchanged, the display will automatically shutoff and all previously recorded data will be lost.• Although the logger continues to work for a period after the battery hasbeen removed, leaving the device without a battery until the LCD displaygoes blank will cause all recorded data to be lost.• After the battery installation, the battery warning mark may not disappearfrom the logger’s LCD for 10 to 60 minutes. This is due to the characteristicof the lithium battery and is not a malfunction of the logger or the battery.Remote Unit Registration and SettingsVia Software and Optical CommunicationConnect the Base Unit to a PC with a USB cable, and place the data log-ger face down to align the communication areas as shown below.<Front> (<LStiydpee>) RTR500BM,Input Modules (Sold Separately) RTR500BW,RTR-500NW/AWRTR-500DCRTR-500MBS-ARTR500BC,RTR-500• Before using the pulse input cable, it is necessary to set the measurement item to “pulsetype” in the Remote Unit Settings of the application.• In order to change the measurement item, initialize the Remote Unit without connect-ing the input module and then redo the Remote Unit registration and settings.Make sure that the module is completelyinserted until you hear a “click” sound.Via Mobile App and Bluetooth® CommunicationWhen the Base Unit is a RTR500BW or RTR500BM, it is possible to makeBase Unit and Remote Unit settings from nearby mobile devices usingBluetooth.Wireless Data RecorderRTR505B User’s ManualRTR505B requires a Base Unit to carry out wireless communication.(Compatible Base Units: RTR500BC, RTR500BW, RTR500BM, RTR-500MBS-A, RTR-500DC, RTR-500, RTR-500NW/AW)For the operation and configuration of the Base Unit, refer tothe instruction manual attached to the Base Unit or the RTR500BSeries Help available on T&D Website.Measurement Item Input Module LCD Displayed ItemsTemperature(Type K, J, T, S)Thermocouple Module(TCM-3010)Measurement, Unit of Measurement,Sensor Type, Operational StatusTemperature(Pt100, Pt1000)PT Module(PTM-3010)Measurement, Unit of Measurement,Sensor Type, Operational StatusVoltage Voltage Module(VIM-3010)Measurement, Unit of Measurement,Operational Status4-20mA 4-20mA Module(AIM-3010)Measurement, Unit of Measurement,Operational StatusPulse Pulse Input Cable(PIC-3150)Measurement, Unit of Measurement,Operational Status

/ 2

This manual is suitable for:

RTR505B

manualsdatabase

Your AI-powered manual search engine