ebm-papst S2E300-AP02-50 Operating Instructions Manual

Also see for S2E300-AP02-50: Operating instructions

ebm-papst S2E300-AP02-50 Operating Instructions Manual Manual pdf 1 page image

Operating instructionsS2E300-AP02-50Translation of the original operating instructionsebm-papst Mulfingen GmbH & Co. KGBachmühle 2D-74673 MulfingenPhone +49 (0) 7938 81-0Fax +49 (0) 7938 81-110info1@de.ebmpapst.comwww.ebmpapst.comCONTENTS1. SAFETY REGULATIONS AND NOTES11. SAFETY REGULATIONS AND NOTESPlease read these operating instructions carefully before starting to workwith the device. Observe the following warnings to prevent malfunctionsor physical damage to both property and people.These operating instructions are to be regarded as part of this device.If the device is sold or transferred, the operating instructions mustaccompany it.These operating instructions may be duplicated and forwarded forinformation about potential dangers and their prevention.1.1 Levels of hazard warnings11.1 Levels of hazard warningsThese operating instructions use the following hazard levels to indicatepotentially hazardous situations and important safety regulations:DANGERIndicates an imminently hazardous situation which, if notavoided, will result in death or serious injury. Compliance withthe measures is mandatory.WARNINGIndicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. Exercise extremecaution while working.CAUTIONIndicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury or damage of property.NOTEA potentially harmful situation can occur and, if not avoided, canlead to property damage.1.2 Staff qualification11.2 Staff qualificationThe device may only be transported, unpacked, installed, operated,maintained and otherwise used by qualified, trained and authorisedtechnical staff.Only authorised specialists are permitted to install the device, to carryout a test run and to perform work on the electrical installation.1.3 Basic safety rules11.3 Basic safety rulesAny safety hazards stemming from the device must be re-evaluatedonce it is installed in the end device.The local industrial safety regulations must always be observed whenworking on the device.Keep the workplace clean and tidy. Untidiness in the working areaincreases the risk of injury.Observe the following when working on the unit:; Do not make any modifications, additions or conversions to thedevice without the approval of ebm-papst.1.4 Electrical voltage11.4 Electrical voltage; Check the electrical equipment of the device at regular intervals, referto chapter 5.2 Safety test.; Replace loose connections and defective cables immediately.DANGERElectrical load on the deviceRisk of electric shock→ Stand on a rubber mat if you are working on an electricallycharged device.21.5 Safety and protective functions21.6 Electromagnetic radiation21.7 Mechanical movement21.8 Emission21.9 Hot surface21.10 Transport21.11 Storage32. PROPER USE43. TECHNICAL DATA43.1 Product drawing53.2 Nominal data53.3 Data in accordance with ecodesign regulation EU 327/201153.4 Technical features63.5 Mounting data63.6 Transport and storage conditions64. CONNECTION AND START-UP64.1 Connecting the mechanical system64.2 Connecting the electrical system74.3 Connection in terminal box94.4 Connection screen104.5 Open additional screwed cable glands104.6 Checking the connections104.7 Switch on device104.8 Switching off the device105. MAINTENANCE, MALFUNCTIONS, POSSIBLECAUSES AND REMEDIES115.1 Cleaning115.2 Safety test125.3 DisposalItem no. 11684-5-9970 · ENG · Revision 205408 · Release 2019-11-16 · Page 1 / 12ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com