ebm-papst W3G990-DZ02-35 Operating Instructions Manual

Also see for W3G990-DZ02-35: Operating instructions

ebm-papst W3G990-DZ02-35 Operating Instructions Manual Manual pdf 1 page image

Operating instructionsW3G990-DZ02-35Translation of the original operating instructionsebm-papst Mulfingen GmbH & Co. KGBachmühle 2D-74673 MulfingenPhone +49 (0) 7938 81-0Fax +49 (0) 7938 81-110info1@de.ebmpapst.comwww.ebmpapst.comCONTENTS1. SAFETY REGULATIONS AND NOTES11. SAFETY REGULATIONS AND NOTESPlease read these operating instructions carefully before starting to workwith the device. Observe the following warnings to prevent malfunctionsor physical damage to both property and people.These operating instructions are to be regarded as part of this device.If the device is sold or transferred, the operating instructions mustaccompany it.These operating instructions may be duplicated and forwarded forinformation about potential dangers and their prevention.1.1 Levels of hazard warnings11.1 Levels of hazard warnings These operating instructions use the following hazard levels to indicatepotentially hazardous situations and important safety regulations:DANGERIndicates an imminently hazardous situation which, if notavoided, will result in death or serious injury. Compliance withthe measures is mandatory.WARNINGIndicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. Exercise extremecaution while working.CAUTIONIndicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury or damage of property.NOTEA potentially harmful situation can occur and, if not avoided, canlead to property damage.1.2 Staff qualification11.2 Staff qualificationThe device may only be transported, unpacked, installed, operated,maintained and otherwise used by qualified, trained and authorisedtechnical staff.Only authorised specialists are permitted to install the device, to carryout a test run and to perform work on the electrical installation.1.3 Basic safety rules11.3 Basic safety rulesAny safety hazards stemming from the device must be re-evaluatedonce it is installed in the end device.Observe the following when working on the unit:; Do not make any modifications, additions or conversions to thedevice without the approval of ebm-papst.1.4 Electrical voltage11.4 Electrical voltage; Check the electrical equipment of the device at regular intervals, referto chapter 6.2 Safety test.; Replace loose connections and defective cables immediately.WARNINGTerminals and connections have voltage even with aunit that is shut offElectric shock→ Wait five minutes after disconnecting the voltage at all polesbefore opening the device.CAUTIONIn the event of failure, there is electric voltage at therotor and impellerThe rotor and impeller are base insulated.→ Do not touch the rotor and impeller once they are installed.21.5 Safety and protective functions21.6 Electromagnetic radiation21.7 Mechanical movement21.8 Emission21.9 Hot surface21.10 Transport21.11 Storage31.12 Disposal32. PROPER USE43. TECHNICAL DATA43.1 Product drawing53.2 Nominal data53.3 Data according to ErP directive53.4 Technical features53.5 Mounting data63.6 Transport and storage conditions63.7 Electromagnetic compatibility64. CONNECTION AND START-UP64.1 Connecting the mechanical system64.2 Connecting the electrical system74.3 Connection in terminal box84.4 Factory settings94.5 Connection screen104.6 Checking the connections104.7 Switch on device104.8 Switching off the device105. INTEGRATED PROTECTIVE FUNCTIONS116. MAINTENANCE, MALFUNCTIONS, POSSIBLECAUSES AND REMEDIES116.1 Cleaning126.2 Safety testItem no. 51477-5-9970 · ENG · Revision 82871 · Release 2015-05-12 · Page 1 / 12ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com