hager EG110 Instructions For Use Manual
1 6E 6129.c6E 6129.conoffONOFFenterresetprogautomanuEG110§ 1 channel time switch -daily cycle.User instruction™EG1103 4 5 621LNTechnical specifications :Electrical characteristics :- supply voltage : 230V +10/-15% 50Hz- output : 1 changeover contactμ 16A - 250V AC1.μ 3A - 250V cos φ = 0,61000 W incandescent lighting- power consumption : 1 VA- protection degree : IP20- insulation class : IIFunctional characteristics :- accuracy : ± 1sec. / day at 20 °C- operating reserve : lithium battery,total of three years.Environment :Operating temperature : -10 to +50 °CStorage temperature : -10 to +50 °CConnection tunnel terminals :flexible : 0,5 to 2.5 mm 2rigid : 0,5 to 4 mm 2Dimensions : 3 modules (3x17,5mm)Electrical connections :1. Move mode selector to “manu”.2. Select the state of the output with key“on/off”.3. Input with key “+” and “-” the overrideduration : from 1 to 23 hours by steps of1 hour.Then from 1 to 27 days by steps of 1 day.4. Move mode selector to “auto”.The state indication is flashing. This means atimed override. Return to the initial programafter the duration.To reset the time switch :Press “reset“ to clear the program.1. Move mode selector to “manu”.2. Press key “-” or “+” until display -h.3. Move mode selector to “auto” to switchback to automatic mode.Timed override :enterresetonoffprogautomanuONenterresetonoffprogautomanuONA warranty period of 24 months is offered on hager products,from date of manufacture, relating to any material of manufac-turing defect. If any product is found to be defective it must bereturned via the installer and supplier (wholesaler). The warrantyis withdrawn if :- after inspection by hager quality control dept the device isfound to have been installed in a manner which is contrary toIEE wiring regulations and accepted practice within the industry atthe time of installation.- the procedure for the return of goods has not been followed.Explanation of defect must be included when returning goods.Warranty GBWorking principle :The EG110 is a time switch for the automaticcontrol of electrical loads.It is fully programmable with a maximum of 20program steps.The front cover is sealable preventingunauthorised access after completion ofprogramming.Warning : at the beginning of use, pleasereset the device in order to clear the memorybefore programming.This is achieved by using a pen to push thereset button.Presentation :Display : time circuit status (ON or OFF)Buttons : Mode selector : to select one of thefollowing modes :time settingprog programmingauto running modemanu manual override “on/off” : chooses whether the circuitis on or off “+” and “-” : changes settings “enter” : to confirm “reset”Time setting :1. Move mode selector to2. Input time with buttons “+” and “-”.Important :The clock starts when leaving the time setting mode.Programming :1. Move mode selector to “prog”.2. Input the switching time with buttons “+” and “-”.3. Input the type of switching with button “on/off”(for the first action ON is automatically proposed).4. Enter this program step with button “enter”.Program additional time settings by repeatingsteps 2 to 4.Important :To activate the program, move mode selector to“auto”.Running mode AutoThis mode is the current displaying mode.It does not allow any modification.Move mode selector to “auto”.Display of the time and the state of the channel.To check your program :1. Move mode selector to “prog”.2. Press the “enter” key repeatedly to displaythe different program steps (switching timeand state of the channel ON or OFF).To override the output :Permanent override :1. Move mode selector to “manu”.2. Select the state of the output with key“on/off”.To switch back to automatic mode, movemode selector to “auto”.51 324 6 7enterresetonoffprogautomanuOFFenterresetonoffprogautomanuTo modify or delete a program step :1. Move mode selector to “prog”.2. Press “enter” repeatedly and select theprogram step to modify or to delete.3. Modify :- switching time with keys “+” or “-”- state of the channel with key “on/off”.To delete a program step, modify switchingtime with keys “+” and “-”, until display --:--(between 23:59 and 00:00).4. Confirm with the “enter” key.enterresetonoffprogautomanuONenterresetonoffprogautomanuONenterresetonoffprogautomanuONTo cancel the timed override :http://waterheatertimer.org/Hagar-timers-and-manuals.html_________________________________________________________________________ |
Related manuals for hager EG110
hager EG171 Instructions For Use Manual
hager EG010 Instructions For Use Manual
hager EG210 Instructions For Use Manual
hager EG270 Instructions For Use Manual
hager EG071 Instructions For Use Manual
hager EG470 Instructions For Use Manual
hager EH710 Instructions For Use Manual
hager EG293B Instructions For Use Manual
hager EG203E Instructions For Use Manual
hager EH716 Instructions For Use Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine