hager TYB692C Quick Start Manual
1Window interface / flush-mountedFensterschnittstelle / UpzeTYB692C6LE000839A 825734076LE000839ADevice componentspicture1: Window interface(1) Control cable(2) Programming button and LED(3) Connection of mains and power cablesSafety instructions• Electrical equipment may only be installed andfi tted by qualified electricians.• Failure to observe the instructions may causedamage to the device and result in fi re andother hazards.• The device is not suitable for disconnectionfrom supply voltage.• The connected actuators are not electricallyisolated from the mains - even when switchedoff.• Do not connect any external voltage to theinputs, since doing so may damage the device(s), and the SELV potential on the KNX bus linewill no longer be available.• For parallel connection of several drivesto an output it is indispensable to observethe corresponding instructions of themanufacturers, and to use a cutoff relayif necessary. There is otherwise risk ofirreparable damage to the drives.• Use only Venetian blind drives with mechanicalor electronic limit switches. Check the limitswitches for correct adjustment. Observe thespecifications of the motor manufacturers.• These instructions are an integral part ofthe product, and must remain with the endcustomer.Product characteristics- Control of Venetian blinds, awnings and similarblinds- Control of electrothermal actuators- Three binary inputs for potential-free contacts,usable as extension inputs for local operation- Supply via bus, no additional power supplynecessaryVenetian blind function- Blind position directly controllable- Slat position directly controllable- Feedback of movement status, blind position andslat position- Forced position through higher-level controller- Safety function: 3 independent wind alarms, rainalarm, frost alarm- Sun protection functionActuator function- Switching operation or PWM operation- Actuators with characteristics opened or closedwithout power- Overload-protected, short circuit-protected- Protection against jamming valves- Forced position- Cyclical monitoring of the input signalsconfi gurable.€i PWM operation: electrothermal actuators onlyhave the positions Open and Closed. In PWMoperation, switch-on and switch-off during thedrive's cycle time achieves an almost constantbehaviour.Information for qualified electriciansFitting and electrical connectionq DANGER!Electrical shock when live parts aretouched.Electrical shocks can be fatal.Before working on the device,disconnect the power supply andcover up live parts in the workingenvironment.Connection assignment, power cablesBK, black: connection LBN, brown: connection of Venetian blind, upPK, pink: connection of Venetian blind, downGY, grey: actuator connectionConnection assignment of control cablepicture 2: Window interfaceRD, red: KNX+BK, black: KNX–GN, green: input 1YE, yellow: input 2WH, white: input 3BN, brown: COM inputs 1...3FunctionSystem informationThis device is a product of the KNX system andcomplies with the KNX directives. Detailed technicalknowledge obtained in KNX training courses is aprerequisite to proper understanding.The function of this device depends upon thesoftware. Detailed information on loadable softwareand attainable functionality as well as the softwareitself can be obtained from the manufacturer´sproduct database.Planning, installation and commissioning of thedevice are carried out with the aid of KNX-certifiedsoftware. Full functionality with KNX commissioningsoftware version ETS3.0d onwards.An updated version of the product database,technical descriptions and conversion programsand other auxiliary programs are available on ourInternet website.Intended purposeWindow interface (picture 1):- Switching of electrically-driven Venetian blinds,awnings and similar blinds for AC 230 V mainsvoltage.- Switching of electrothermal actuators- Installation in appliance box to DIN 49073- Connection with enclosed terminalsBn,.:V2.7.0V2.7.0 |
Related manuals for hager TYB692C
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine