jablotron JA-116E Manual
The JA-116E / JA-116E-AN / JA-116E-GRBUS touchscreen keypad with RFID readerTyp: 1KPAD2203RNJA-116E / JA-116E-AN / JA-116E-GR 1 / 3 MRN51603The keypad is a component of the JABLOTRON system and isdesigned to be operated by touch. The keypad must be installed bya trained technician with a valid Jablotron certificate issued by anauthorised distributor. This product is compatible with JA-103Kand JA-107K control panels.This manual must be used together with the installation anduser manual of the JABLOTRON control panel system.The keypad components are shown in the following figures:Figure 1 – front part: 1 – touchscreen; 2 – button/system indicator;3 – RFID reader – reading areaFigure 2 – internal part: 4 – connection points of the BUS terminal;5 – serial number; 6 – tamper contacts; 7 – USB-C connector;8 – locking mechanism; 9 – rear part tabFigure 3 – mounting pad: 10 – BUS terminalInstallation1. Remove the mounting pad (Fig. 3) of the keypad. If it cannot beremoved easily, open the locking mechanism, see chapter “Keypaddisassembly”.2. In the mounting pad, break out the blank of appropriate slot, pullthe BUS cable through, and then screw the mounting pad of thekeypad to the designated place, preferably on a solid base (wall).Select the installation height of the keypad with respect to theheight of the users. The ideal height for good readability andcontrol is at eye level. It is not recommended to mount at a heightconsistent with electrical switches (100-110 cm).3. Connect the individual wires of the BUS cable to the BUSterminal (10) as follows:a) Using a flat screwdriver to press upper side of the terminal.b) Put a stripped wire into the appropriate terminal.c) Release the terminal.d) Test if the wire is correctly fixed with a gentle pull.+U – red; positive power supply poleA – yellow; data wire AB – green; data wire BGND – black; negative power supply poleNotes:− Connect only straight, stripped wires to the BUS terminals(their ends only).− Use a narrow flat screwdriver to turn the locking mechanismand release the tab.Always switch the power off beforeconnecting the keypad to the BUS.4. First, attach the bottom edge of the keypad to the mounting pad(align the bottom sides) and slide in downwards until you hear theclick of the tab (9). This will secure the keypad against falling out ofthe mounting pad. Then turn the locking mechanism (8) clockwise90° to the position where the groove points to the symbol . Thislocks the keypad in place and engages the tamper contact.5. Power the system on.6. Enrol the keypad to the system according to the type of controlpanel, use the recommended software or application, see theinstallation manual of the control panel.Notes:− Enrolment is possible by entering the serial number (5) in theF-Link software or appropriate application. All numbers statedunder the bar code must be entered (1400-00-0000-0001).− Another enrolment option is using F-Link software, within theDevices tab -> Scan/Add new BUS devices; or by pressing thebutton (2).Keypad disassemblyOn the underside of the keypad, turn the locking mechanism (8)counterclockwise 90° until the groove points to the symbol . Insertthe flat screwdriver into the tab hole (9) (push the screwdrivertowards the wall) while sliding the keypad upwards. The keypad canthen be easily removed from the mounting pad.Authorisation – can be done by entering a valid access code onthe virtual keypad or by applying the access card / chip. Authorizationwill terminate itself after 15 seconds from the last detected touch onthe screen, or immediately by pressing the button (2), or it can beterminated by the logout icon in the upper left corner. The individualkeypad screens and menus and the system control options arebased on the user access rights configured in the control panel. |
Related manuals for jablotron JA-116E
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine