jablotron JA-150P PET Manual
  |
JABLOTRON ALARMS a.s.Pod Skalkou 4567/33 46601 Jablonec n. NisouCzech Republic www.jablotron.com| ||JA-150P PET Wireless PIR motion detector with basic pet immunityJA-150P PET Wireless PIR motion detector with basic pet immunity 1 / 2 MMB56101The JA-150P PET is a wireless device of the JABLOTRON 100system. It is used to detect movement of persons in interiorsof buildings. Unlike the standard PIR motion detectors formthe JABLOTRON 100 series, this detector has a modified detectioncharacteristic and it is equipped with basic pet immunity. The detectoreliminates the effect of the movement of small animals on the floor(animals with a weight of up to approx. 25 kg and a maximum heightof 40 cm). The detector has a pulse reaction and it takes one positionin the system. The detector should be installed by a trained technicianwith a valid certificate issued by an authorized distributor.InstallationThe detector can be installed onto a wall or in a corner of a room.Bear in mind that the detector’s field of vision should not include anyobjects which quickly change temperature (electrical heaters, gasappliances, etc.) or which move (curtains hanging above a radiator,robotic vacuum cleaner, etc.). Although the detector is very resistantto false alarms, it is not recommended to install the detector in placeswith intense air circulation (close to ventilators, air conditioning, vents,unsealed doors etc.). There should not be any obstaclesin the detector’s field of vision that would obstruct its view intothe guarded area.The recommended detector installation height is 2 m, maximumheight 2.2 m.I.II.12453Figure 1.: 1 – holes for installing on a flat wall; 2, 4 – holes for installing at an angle(in a corner); 3 – PCB tab; 5 – cover tab1. Open the detector cover by pressing the cover tab (5). Avoidtouching the PIR sensor inside (10) – you could damage it.2. Take out the PCB – it is held by a tab (3).3. Punch through the holes for screws in the plastic base and attachit to the wall. The recommended detector installation height is 2 mabove the floor.4. Insert the PCB back and proceed by following the control panelinstallation manual. Basic instructions:a. Open the F-Link software, select an unused positionin the Devices tab and click on the Enroll button to enterthe Enrollment mode.b. Insert both batteries into the detector (mind the correctpolarity). After the second battery is inserted into the detectorthe enrollment signal is transmitted to the control panel andthe detector is enrolled to the selected position. This is followedby up to a three-minute detector stabilization phase indicatedwith a flashing LED.5. Close the detector cover and test the detector’s function.Figure 2.: 6 – red activation LED; 7 – batteries; 8 – production code; 9 – cover tampersensor; 10 – PIR sensorNotes:- The detector can also be enrolled into the system by entering itsproduction code in the F-Link software. You can find the productioncode on the sticker (8) placed on the detector board. All numbersunder the bar code must be entered (1400-00-0000-0001).- If you want to remove the device from the system, erase it from itsposition in the F-Link software.- Should you enroll the detector into the control panel afterthe batteries have been inserted, first take them out, then press andrelease the tamper sensor (9) to consume the residual energy andafter that enroll the detector to the control panel.- To meet the EN 50131-3 standard it is necessary to securethe cover tab (5) with the supplied screw.Detector function modesThe detector can work in two modes that are indicated with oneor two flashes when inserting the batteries.To change the mode, during battery insertion, press and hold thetamper sensor (9). After inserting the second battery hold the tampersensor for approx. 3 s before releasing. The detector then flashes eitheronce or twice to indicate the currently selected mode. The defaultsetting is Smartwatch.One flash indicates Smartwatch mode that is intended forthe permanent monitoring of movement in the guarded area.If permanent movement is detected, three reports are sent every 20 s.The next report is then sent after 2 minutes. If the detector does notdetect any movement for 10 minutes, the mode with three reports every20 s is used again.Two flashes indicate one-minute interval mode. When a movementis detected, it sends a report and goes into standby mode for 1 minute.When the time is over, the detector wakes up and remains active untilthe next detection of movement.Detector testingFor a period of 15 minutes after closing the detector cover, the LED(6) indicates all movement and reports it to the control panel. After thistime the detector switches to the mode selected during battery insertion.Individual activations of the detector can also be monitoredin the Diagnostics tab in the F-Link software.Battery replacementThe system automatically reports a low battery status.We recommend replacing the batteries within two weeks from the lowbattery report. It is done by a service technician in service mode.Always replace both batteries at the same time!Before inserting new batteries, it is necessary to wait for 10 sor to press the tamper sensor (9) to consume the residual energy.Detection characteristicsThe detector is fitted with a lens covering 90° / 12 m as standard, seethe following figure. In the white part of the diagram the detectoreliminates the effects of movement of small animals with a weightof up to approx. 25 kg and a maximum height of 40 cm, in the grey partof the diagram there is standard detection.2mmax 2,2m90°024624688 0 2 4 6 8 10 127Figure 3.: Detection characteristicsThe detector eliminates only the effectsof movement of animals on the floor accordingto the detection characteristics.It is not suitable for guarding areas whereanimals can move freely at height! |
Related manuals for jablotron JA-150P PET
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine