nedis ACMB1WT12 User Manual
Also see for ACMB1WT12: Quick start guide
Description EnglishDevice (fig. A)1. Control panel2. Air outlet3. On/off button • Press the button to switch on or off the device.4. Mode button • Repeatedly press the button to select the mode: Cooling mode / Dehumidifyingmode / Fan mode.5. Up button6. Down button• Cooling mode: Press the up button or the down button to change the settemperature. Simultaneously press both buttons to switch between Celsius (°C)and Fahrenheit (°F).• Press the up button or the down button to change the set timing value.7. Timer button • Press the button to set the timer.Note: The timer can be set upto a maximum of 24 h.8. Wind Speed selectionbutton• In cooling or fan mode, press the button repeatedly to select the fan speed: Low/ Medium / High.• In dehumidification mode the wind speed selection button is invalid. The fanremains in low wind speed operation.9. Display window • The display window shows the set temperature or the set timing.10. Cooling mode indicator • This indicator shows that the device is in cooling mode.11. Dry mode indicator • This indicator shows that the device is in dehumidifying mode.12. Fan indicator • This indicator shows that the device is in fan mode.13. Water reservoir indicator • This indicator shows that the water reservoir needs drainage.14. Celsius indicator • This indicator shows that the temperature is set in Celsius (°C).15. Fahrenheit indicator • This indicator shows that the temperature is set in Fahrenheit (°F).16. Hr indicator • This indicator shows that the device is in timer mode.17. Sleep mode indicator • This indicator shows that the device is in sleeping mode. This function is onlyavailable in cooling mode. Simultaneously press buttons 5 and 8 to activate.18. On/off indicator • This indicator shows that the device is on or off.19. Handle20. Continous drainage hole• In the cooling and dehumidification mode continuous draining is possible:• Unplug the water plug and connect the water outlet to a water container ordrainage.21. Power cord fixing board22. Remote control holder23. Drainage hole• To drain the device, switch off the device and disconnect the power plug of themains socket.• Loosen the drainage cover and unplug the water plug. Let the water flow into awater container. Connect the water plug and tighten the drainage cover.24. Air filter • For an optimum filtration clean the filter frame and inner filter regularly.25. Exhaust connector26. Air filter • For an optimum filtration clean the filter frame and inner filter regularly.27. Wheels • Place the device on a flat and dry surface.28. Power cord29. Exhaust pipe• Connect the exhaust pipe to the exhaust connector and the connector of thewindow adapter. The length of the exhaust hose must be between 28 and150 cm.Do not use extension tubes. Make sure that the exhaust is unobstructed.30. Connector of the windowadapter • The device can be placed in horizontal or vertical direction.Remote control (fig. B)1. Remote control • Use the remote control to control the device from a distance of maximum 5 m.2. On/off button • Press the button to switch on or off the device.3. Timer button • Press the button to set the timing value.4. Swing button • Press the swing button to open or close swing style. The air flow of the air outlet canblow at different angles.5. Sleep mode• In cooling mode, press the button to select sleep mode.Note: After selecting the sleep mode the temperature increases by 1 °C after onehour and again 1 °C after two hours. After two hours the temperature remainsconstant.6. Up button7. Down button• Press the up button to increase the temperature or the timing set value.Note: The temperature can be set to a minimum of 16 °C and a maximum of 31 °C.• Press the down button to decrease the temperature or the timing set value.8. Mode selection button • Repeatedly press the button to select the mode: Cooling mode / Dehumidifyingmode / Fan mode.9. Fan button • Press the fan button to select high, medium or low wind speed output.10. Celsius - Fahrenheit button • Press the button to switch between Celsius (°C) and Fahrenheit (°F).Installation (fig. C)• Refer to the illustration to install the device.Note: The distance between the device and the wall or other objects must be at least 50 cm.Protection functions• The device has five protection functions: Frost protection function, overfow protection, automatic defrosting,automatic thermal protection and protection of the compressor.ACMB1WT12Local air conditionerTIMERF AN UP DOWN MODE POWERCoolDryFanFullSLEEPºCºFHrSleepon/oCoolDryFanFullºCºFHrSleepon/off262024212213 712111018171514168 5 69 4 32127293019232528A30BCCoolºC1543ºC ºF 10982 67 |
Related manuals for nedis ACMB1WT12
nedis ACMB1WT14 Quick Start Manual
nedis ACMB1WT9 Quick Start Manual
nedis ACMB1WT7 Quick Start Manual
nedis SmartLife WIFIACMB3WT9 User Manual
nedis ACMB2BK12 Quick Start Manual
nedis WIFIACMB1WT16 Quick Start Manual
nedis WIFIACMB1WT14 Quick Start Manual
nedis ACMB2WT9 Quick Start Manual
nedis WIFIACMB1WT7 Quick Start Manual
nedis WIFIACMB1WT9 Quick Start Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine