The NodOn® Octan remote can be added and operated in any Z-Wave® networkwith other Z-Wave® certified devices from other manufacturers and/or otherapplications.All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliabilityof the network.It has 2 distinctive working modes:1. «STANDALONE» MODEThe Octan remote can control Z-Wave® compatible devices directly, such as theNodOn® Smart Plug or a light dimmer, whoever is the manufacturer.Note: No home automation gateway is involved and necessary in this mode.2. «GATEWAY» MODEThe Octan remote is in “Gateway” Mode as soon as it is added in a Z-Wave®network managed by a home automation gateway. The remote control becomesthen the gateway’s assistant, capable to launch up to 16 different scenes through it(SCENE Profile) or directly associated to your Z-Wave® compatible devices (MONOor DUO Profile).WALL SUPPORTA magnetic wall support is included with your Octan Remote. This support can bescrewed (screws not included) or fixed by adhesive bonding (included).The remote control embeds a small magnet, allowing fixing it on its wall supportor on any metallic surface (fridge door, heater, etc.).USAGEBATTERY REPLACEMENTThe Octan remote operates using a CR2032 coin cell battery (included).To replace the battery, slide slowly the battery cover, located on the backside of theremote.Before the first use, take care of removing the battery protector, after opening thebattery cover.Careful : In order to save as much as possible the battery life time, avoid long learning process, and place the remotecontrol as close as possible to the device you want to associate.OCTAN REMOTE INTERFACEThe remote control has 4 buttons and one LED located at the center of the product.BATTERY LEVELIn order to know the battery level, a simultaneous short press onI and P mustbe performed. The LED will display the battery level according to below table:LED state Battery levelGreen Under 50%Orange Between 50 and 20%Red Below 20%FACTORY RESETA factory reset will completely delete the memory of the remote control andrestore all the parameters to default value.A simultaneous long press (1sec) on O and M will perform this factory reset.The LED will blink red and green to validate the resetCareful : In “Standalone” Mode, make sure to remove all the devices added or associated in the remote control’snetwork before performing a factory reset.In “Gateway” Mode, use the factory reset procedure only when the PrimaryController (i.e. the gateway) is missing or defective. Reset the remote controldoes not mean that it has been removed from the Primary Controller memory.Remove the remote controller (through the Primary Controller) before performinga factory reset.« STANDALONE » MODEBy default, the Octan remote is in “Standalone” Mode. It means it can controlcompatible Z-Wave® devices without involving the gateway. The Octan remote actsas the Primary Controller of the network.While the remote control is in “Standalone” Mode, you can:•Control one or several devices (up to 8) with only 1 button: MONO Profile.•Control one or several devices (up to 8) with 2 buttons: DUO Profile.Careful : You must not unplug a Z-Wave® device definitely without removing it from the remote control’s Z-Wave®network first (See the “Exclusion” part below). This can have a serious impact on the battery lifetime.ASSOCIATIONCareful : Before associating a device which was not recently bought, please perform an ”EXCLUSION” first. Pleaserefer to the “Exclusion” section below.Association is performed in 3 steps:1 Push 3 times (quickly) on the I button to activate the “Association” Mode.The LED glows in blue2 Choose which button will control your device, within 10 seconds.• A short press on one of the buttons of the remote control (I, O, P orM) will activate the MONO Profile. The pressed button will then controlyour device.• A long press on the I button will activate the DUO Profile, combinedwith the O button. The I (ON) and O (OFF) buttons will then controlyour device.• A long press on the P button will activate the DUO profile, combinedwith the M button. The P (ON) and M (OFF) buttons will then controlyour device.The LED blinks in blue to confirm your choice3 Place the device you want to associate in “Learning” Mode, within 10 seconds.To do so, please refer to your device’s user guide.The LED of the remote control blinks green to confirm the association processCareful : In case of a too long association process or others problems during the process, the LED will blink red.Please restart the procedure.Once the association is validated, your remote control is able to control yourdevice. Different actions are possible.1. MONO PROFILEThis profile allows controlling your associated device(s) using just a single buttonof the Octan remote.A short press on I, O, P or M (depending on your choice during associationprocess) will activate (ON) your associated device(s), a second short press willdeactivate (OFF) your associated device(s).If your device has dimming features (light dimmer, roller shutter, etc.):• A long press on the I, O, P or M (depending on your choice duringassociation process) will dim up your associated device (light, rollershutter, etc.) until you release the button.• A second long press on the same button will dim down your associateddevice (light, roller shutter, etc.) until you release the button.2. DUO PROFILEThis profile allows controlling your associated device(s) with two mutual buttons.• A short press on I (or P depending on your combination choice duringassociation process) will activate (ON) your associated device(s).• A short press on O (or M depending on your combination choice duringassociation process) will deactivate (OFF) your associated device(s).If your associated device(s) has dimming features (light dimmer, roller shutter, etc.):• A long press on I (or P depending on your combination choice duringassociation process) will dim up your associated device (light, rollershutter, etc.) until you release the button.• A long press on O (or M depending on your combination choice duringassociation process) will dim down your associated device (light, rollershutter, etc.) until you release the button.Carful : It is not possible to cumulate a MONO and DUO profile on the same button.Repeat the association process as many times as you want to associate a newdevice.DISASSOCIATIONThe disassociation deletes any association relationship between the device andthe remote control’s buttons. However, your device will remain in your remotecontrol’s Z-Wave® network.1 Push 3 times (quickly) on the P button.The LED blinks in blue2 Place the device you want to disassociate in “Learning” Mode, within 10seconds. To do so, please refer to your device’s user guide.The LED blinks in green to confirm the disassociationINCLUSIONInclusion allows adding a device into the remote control’s Z-Wave® network,without associating it with any buttons of the remote control. The remote controlwill then not be able to control your added device.1 Push 3 times (quickly) on the O button.The LED blinks in blue2 Place the device you want to add in “Learning” Mode, within 10 seconds. To doso, please refer to your device’s user guide.The LED blinks in green to confirm the inclusionOCTAN Remote with wall supportReference: CRC-3-1-0xPower supply: CR2032 batteryRadio frequency: 868MHzRange up to 80 meters outdoorRange up to 40 meters indoorOperational temperature: -10°C / 50°CIP20Radio protocol: Z-Wave Plus® (500 series)Dimensions: 80 mm (L) x 80 mm (l) x 17.5 mm (h)Weight: 68 g (with wall plate)Warranty: 2 yearsUSER GUIDEOCTAN REMOTEONOFFONUpDownUpDownOFFON & OFFON & OFFON & OFFUp & DownUp & DownUp & DownUp & DownON & OFF |
Related manuals for nodon OCTAN
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine