wattstopper LMPL-101 Quick Start Manual

wattstopper LMPL-101 Quick Start Manual Manual pdf 1 page image

SwitchCeiling MountOccupancySensorPlug LoadControllerLine Voltage(Class 1 wiring)To Plug Load(Class 1 wiring)J-BoxTo OtherElectricalOutletsLMPL-101Digital Lighting Management (DLM)Digital Plug Load Room ControllerInput Voltage:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120VAC, 50/60HzLoad Requirements:Maximum Duplex Receptacle Rating . . . . . . . . . . . . . 120VAC, 20AOutput . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mA @ 24VDCDLM Local Network Characteristics for LMPL-101 or LMRC-10x:Provides 24VDC power over Cat 5e cable and RJ-45 connectorsSupports up to 24 communicating devices, including 4LMRC-10x or LMPL-101 controllersFree topology up to 1,000ft of low voltage cableEnvironment:Operating Temperature. . . . . . . . . . . . . .32° to 104°F (0° to 40°C)Storage Temperature . . . . . . . . . . . . . .23° to 176°F (-5° to 80°C)Relative Humidity. . . . . . . . . . . . . . . . . 5 to 95% (non condensing)Patent PendingQuick Start GuideQuick Start GuideCONNECTIVITYThe LMPL-101 communicates with all other DLM devicesconnected to the DLM local network. Connection drawingsare for example only. The low voltage LMRJ cables canconnect to any DLM device with an open RJ45 receptacle.All line voltage wiring is #12 AWG.LineVoltageRoomControllerSwitchCeiling MountSensor Low VoltageDLM Local NetworkLMRJ CablesPlug LoadControllerLMPL-101 J-Box120VACJ-BoxLoads21White: NeutralYellow toLoad 2 (B)LMRC102Red: Switched120VAC LineRed toLoad 1 (A)GroundSwitchCeiling MountOccupancySensorRoomControllerJ-BoxPlug LoadControllerLine Voltage(Class 1 wiring)To Plug Load(Class 1 wiring)J-Box To LightingLoad(Class 1 wiring)To OtherElectricalOutletsLine Voltage(Class 1 wiring)PLACEMENT EXAMPLESATTACHING CABLESMOUNTING THE CONTROLLERThe LMPL-101 controller can either be mounted external toa junction box, placing it in the plenum space or mounteddirectly inside a 4” x 4” junction box.Outside a 4” x 4” box Inside a 4” x 4” boxRemove rubber jack covers if using all 3 RJ45 receptacles.Leave covers in place for all unused receptacles.WARNING: TO CONNECT A COMPUTER TO THE DLM LOCALNETWORK USE THE LMCI-100. NEVER CONNECT THE DLMLOCAL NETWORK TO AN ETHERNET PORT – IT MAY DAMAGECOMPUTERS AND OTHER CONNECTED EQUIPMENT.LineJ-BoxLoadJ-BoxLoadLineTHIS UNIT IS PRE-SET FOR PLUG n’ GO™OPERATION, ADJUSTMENT IS OPTIONAL.For full operational details, adjustment and morefeatures of the product, see the DLM System InstallationGuide provided with the LMRC-102 room controller,and also available at www.wattstopper.comFOR CONNECTION TO PLUG LOADS ONLY.INSTALLATION SHALL BE IN ACCORDANCE WITH ALLAPPLICABLE REGULATIONS, LOCAL AND NEC CODES.Wire connections shall be rated suitable for the wiresize (lead and building wiring) employed.For Class 2 DLM devices and device wiring:To be connected to a Class 2 power source only.Do not reclassify and install as Class 1, or Power and Lighting Wiring.WARNING: Do not install to cover a junction box having Class 1, 3 orPower and Lighting Circuits.

/ 2

Related manuals for wattstopper LMPL-101