Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Magnetek IMPULSE 5062-VG+S4 manuals

IMPULSE 5062-VG+S4 first page preview

IMPULSE 5062-VG+S4

Brand: Magnetek | Category: Controller
Table of contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. How to Use This Manual
  6. Introduction
  7. IMPULSE®•G+ & VG+ Series 4 General Specifications
  8. AC Reactor Specifications
  9. S4IF Interface Specifications
  10. IMPULSE®•G+ & VG+ Series 4 System Components And External Devices
  11. Long Time Storage
  12. Installing the Drive
  13. Multiple Drive Installation (Side-by-Side Installation)
  14. Drive Derating Data
  15. IMPULSE®•G+ & VG+ Series 4 Wiring Practices
  16. Suggested Circuit Protection Specifications and Wire Size
  17. Power Circuit Wiring Procedures
  18. Main Circuit Connection Diagram
  19. Terminal Block Configuration
  20. Insulation Barrier
  21. Interface Circuit Board
  22. Dip Switches
  23. Sinking/Sourcing Mode Selection for Safe Disable Inputs
  24. Control Circuit Terminals
  25. S4IF Control Circuit Terminal Diagrams
  26. Safe Torque Off
  27. Wiring the Encoder Circuit
  28. Encoder Wiring Diagrams and Information
  29. Overview
  30. Using the Keypad
  31. Keypad LED and Button Functions
  32. Parameter Modes
  33. Initialization Set-up
  34. X-Press Programming™
  35. Initialize Parameters (A01-05)
  36. User Parameters (A02-01 through 32)
  37. Auto-Tuning
  38. Standard Auto-Tune (T01-01 = 0) Instructions
  39. Non-Rotational Auto-Tune (T01-01 = 1) Instructions
  40. Terminal Resistance Auto-Tune (T01-01 = 2) Instructions
  42. Reference Limits
  43. Sequence/Reference Source
  44. Stop Method
  45. Coast to Stop (B03-03=1)
  46. Motor Rotation Change
  47. Acceleration/Deceleration
  48. Accel/Decel Time Switching Frequency
  49. Special Functions
  50. Quick Stop™
  51. Reverse Plug Simulation™
  52. Micro-Speed™
  53. End of Travel Limits
  54. Phantom Stop
  55. Klixon
  56. Hook Height Measurement
  57. Electronic Programmable Limit Switches (EPLS)
  58. Lower Limit/Upper Limit Bypass MFDI
  59. Load Float
  60. OLV and FLV Operation (A01-02 = 02 and 03)
  61. Swift-Lift™ & Ultra-Lift™
  62. Configuring the Swift-Lift & Ultra-Lift Function
  63. Torque Limit
  64. Anti-Shock
  65. No-Load Brake Hoist (VG+)
  66. E-Lift (VG+)
  67. Digital Input Option Set-up (DI-A3 and S4IO)
  68. Weight Measurement
  69. System Tare and Calibration for Weight Measurement
  70. Slack Cable Detection
  71. Snap Shaft Detection
  72. Brake Delay Timers
  73. Maintenance Timer
  74. Inching Control
  75. Index Function
  76. Tuning
  77. Motor Slip Compensation
  78. Automatic Speed Regulator (ASR) Tuning
  79. Torque Control
  80. Speed/Torque Control Switching
  81. S-Curve Acceleration/Deceleration
  82. Carrier Frequency
  83. Hunting Prevention
  84. Motor Parameters
  85. Motor Set-up
  86. Test Mode Configuration
  87. Option Card Parameters
  88. Analog Input (AI-A3) Option Set-up
  89. Analog Output (AO-A3) Option Set-up
  90. Digital Output (DO-A3) and S4IO Option Set-up
  91. Profibus-DP Communication Option Card Set-up
  92. Ethernet Option Card Set-up (Ethernet IP & Modbus TCP/IP)
  93. Terminal Parameters
  94. F1 and F2 Keys Function Selection
  95. Digital Outputs
  96. Digital Outputs—Alarm/Fault Annunciate (H02-01–03=40)
  97. Analog Inputs
  98. Analog Outputs
  99. Serial Communication Set-up
  100. Pulse Train Input/Output
  101. Protection Parameters
  102. Power Loss Ride Thru
  103. Stall Prevention
  104. Speed Agree
  105. Test Mode
  106. Torque Detection
  107. Hardware Protection
  108. Automatic Fault Reset
  109. Fault Latch Selection
  110. Operator Parameters
  111. Keypad Key Selection
  112. Maintenance History
  113. Copy Function
  114. Monitor Parameters
  115. Troubleshooting the Drive
  116. Troubleshooting Encoder Related Faults
  117. Fault Code: PGO-X-S/PGO-X-H–Pulse Generator Signal Fault
  118. Fault Code: BE1–Rollback Fault
  119. Fault Code: BE3–Brake Release Fault
  120. Alarm Code: BE6–Brake Proving Alarm
  121. Fault Code: OC–Over Current Fault
  122. Fault Display and Corrective Actions at Auto-Tuning
  123. Troubleshooting Option Card Related Faults
  124. Copy Function Related Faults
  125. Power Section Check
  126. S4IF Replacement Procedure
Related products
IMPULSE 5062-G+S4IMPULSE 5027-VG+S4IMPULSE 5001-VG+S4IMPULSE 5009-VG+S4IMPULSE 5017-VG+S4IMPULSE 5022-VG+S4IMPULSE 5004-VG+S4IMPULSE 5003-VG+S4IMPULSE 5006-VG+S4IMPULSE 5012-VG+S4
Magnetek categories
Controller
DC Drives
Water Pump
Remote Control
Transmitter
Remote Starter
Battery Charger
Receiver
Power Supply
Industrial Equipment
More Magnetek categories
Manuals database logo
manualsdatabase
Your AI-powered manual search engine