Panasonic LP-GS051-FE manuals
LP-GS051-FE
Table of contents
- Preface
- Cautions in Handling
- How to Read this Document
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Preparation of Command Control
- Operation by External Devices
- Operation procedure with external control
- Settings before external control
- Remote mode settings
- Serial Communication Interfaces
- RS-232C
- Communication settings (LP-400/V compatible mode)
- Ethernet
- Communication settings
- Connecting to external control devices and its setting sample
- Checking the communication commands
- Communication Control Basics
- Communication Data Types
- Communication Sequence
- Communication Data Format
- Request data
- Response data
- Character input method
- Character data input method
- Command Reception Condition
- Commands acceptable only with the shutter closed
- Communication Check
- Control Sample
- Data Format for Each Command
- Command List
- Command Description Details
- Operation Control Commands
- Laser pumping: LSR
- Shutter open/close: SHT
- Marking trigger: MRK
- Trigger delay: DLY
- Guide laser: GID
- Status checking: STS
- Marking end verification: MST
- File Setting Commands
- File selection by name: FNN
- Overwrite file: FOR
- File name: FNM
- Character Setting Commands
- Character entry (by ASCII and Shift-JIS code): STR
- Character entry per trigger: SIN
- Character object settings: STC
- Character object settings (shortened): SPC
- Functional Character Commands
- Counter reset: CTR
- Expiry date/time settings: LMT
- Lot settings: LTC
- Lot period/character: LTS
- Registered character settings: RKC
- Registered character strings: RKS
- Bar Code/2D Code Settings Commands
- Bar code/2D code characters (by ASCII and Shift-JIS code): BRS
- Bar code/2D code object settings: BRF
- Human readable text settings: BRV
- Module filling of 2D codes: BRP
- Command for graphic data settings
- Graphic object settings (VEC format file) : CDC
- Point Radiation Commands
- Point radiation correction: PRF
- Layout/Position Adjustment Commands
- External offset settings: OFC
- External offset values: OFS
- Step & repeat settings: SRC
- Step & repeat fine-adjustment: SRA
- On-the-fly Marking Commands
- Encoder resolution: ENC
- Line speed: LSP
- Workpiece spacing: INT
- Laser Setting Commands
- Scan speed: SSP
- Laser frequency / pulse cycle: MPL
- Laser fine tune: WTC
- Line width / filling line spacing: WDC
- Maintenance Commands
- System Settings Command
- Command mode: RSM
- Troubleshooting
- Error Indication
- Warning: E600 - E799
- Character Code Table
- ASCII Code
- Shift JIS Code
- Index
LP-GS051-FE
Table of contents
- Preface
- Cautions in Handling
- ME-LPGS-SM
- Applicable Standards and Related Regulations
- How to Read this Document
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Product Overview
- Product Model
- Product Configuration
- Package
- Specification
- Outer Dimensional Drawing
- Controller
- Cables
- Name of Each Component
- Laser Marker Installation
- Installation Environment
- Installation Space
- Head Installation
- Installation method
- Marking field and marking center position
- Marking position check
- Controller Installation
- Connecting Laser Marker
- Power connection and earth (Grounding)
- Connection of PC (Laser marker NAVI smart)
- Construction of System
- Operation Method
- Type of Operations
- Start-up & Termination
- Termination procedure
- Operation by PC Configuration Software
- Screen types
- How to establish online connection
- How to disconnect online connection
- How to switch screens
- Test marking and RUN mode
- Operation by External Devices
- Operation procedure with external control
- Settings before external control
- Remote mode settings
- External Control Using I/O
- I/O Interface Specification
- Signals and Details of I/O Terminal Block
- Signals and Details of I/O Connector
- I/O Rating/Circuit
- Output rating and output circuit
- Interlock terminal rating and I/O circuit
- Connecting I/O Terminal Block
- Connecting common terminals
- Sensor connection example
- Checking the I/O terminal status
- Basic Control Timing Chart
- Shutter open/close
- Marking trigger input: Single trigger
- Marking trigger input: Continuous trigger
- Guide laser radiation input
- Select file
- Time/date hold input and date gap output
- Count-up/count-down value correction
- Counter reset input
- Registered characters/external offset marking
- Laser stop 1 input
- Laser stop 2 input
- Interlock input
- External Control by Communication Commands
- Serial Communication Interfaces
- RS-232C
- Communication settings (for command control)
- Ethernet
- Communication settings
- Connecting to external control devices and its setting sample
- Checking the communication commands
- Link Control with External Devices
- Link Control with Image Checker
- Example of image checker linkage system
- Operation flow
- Connection
- Set the laser marker communication settings
- Set the laser marker overall file conditions
- Image checker setting
- Code reader (LP-ABR) setting
- Timing chart
- Link Control with Code Reader
- Preparation of readout code
- Setting of code reader linkage functions
- Maintenance
- Maintenance Items
- Maintenance Details of Parts
- Intake/exhaust vent
- Air filter
- Air-cooling fan
- Laser oscillator
- Galvano scanner
- Z-axis adjustment module
- Replacement of battery inside the controller
- Replacement of fuse
- Obtaining Backup Data
- Serial Number Checking Method
- Disposal of Laser Marker
- Troubleshooting
- Error Indication
- Warning: E600 - E799
- Index
manualsdatabase
Your AI-powered manual search engine