Feig Electronic OBID i-scan ID ISC.LR2000 manuals
OBID i-scan ID ISC.LR2000
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Revision History of documentation
- Abbreviations
- Introduction
- Configuration Commands and Control Commands
- ISO15693 Host Commands
- Buffered Read Mode
- Notification Mode
- Scan Mode
- Reader Multiplex Mode (Syncronisation)
- Interface
- Serial Data Format and Protocol Frames
- CRC16 Calculation Algorithm
- Configuration Parameters (CFG)
- CFG0: Passwords
- CFG1: Interface
- CFG2: Inputs/Outputs I
- Dedicated Input / Output Functions
- CFG3: RF-Interface
- CFG4: Transponder Parameters
- CFG5: Anticollision
- CFG6: Customer Command Option Bytes
- CFG7 Reserved
- CFG8: People Counter
- CFG9: Input / Output II (Assignment – output to antenna read event)
- CFG10: Trigger
- CFG11: Read Mode /Scan Mode – Read Data
- CFG12: Read Mode - Filter
- CFG13: Scan-Mode
- CFG14: Reserved
- CFG15: Antenna Multiplexing I
- CFG16: Persistence Reset
- CFG17: Antenna Multiplexing II
- CFG18: Reader Synchronisation
- CFG19: Reserved
- CFG20: RF-Parameter
- CFG22 + CFG23: Selection Mask (only I-Code UID and EPC Transponder)
- CFG24 .. 29: Reserved
- CFG40: LAN Settings, Part 1
- CFG41: LAN Settings, Part 2
- CFG42: WLAN Settings, Part 1
- CFG43: WLAN Settings, Part 2
- CFG44 WLAN Security Settings, Part 1
- CFG45 WLAN Security Settings, Part 2
- CFG46: People Counter Notification Channel
- CFG49: Notification Channel
- CFG63: Customer Parameter
- Protocols for Reader Configuration
- x81] Write Configuration
- x82] Save Configuration
- x83] Set Default Configuration
- x87] Set System Time and Date
- Protocols for Reader Control
- x52] Baud Rate Detection
- x63] RF Controller Reset
- x66] Get Reader Info
- x69] RF Reset
- x6A] RF Output ON/OFF
- x6D] Get Noise Level
- x6E] Reader Diagnostic
- x72] Set Output
- Set Output Examples
- x74] Get Input
- Protocols for ISO15693 Host Commands
- xB0] Host commands for ISO15693 Mandatory and Optional Commands
- x01] Inventory
- x02] Stay Quiet
- x22] Lock Multiple Blocks
- x23] Read Multiple Blocks
- x24] Write Multiple Blocks
- x25] Select
- x26] Reset to Ready
- x27] Write AFI
- x28] Lock AFI
- x29] Write DSFID
- x2A] Lock DSFID
- x2B] Get System Information
- x2C] Get Multiple Block Security Status
- xBF] ISO15693 Transparent Command
- Supported ISO15693 Host commands
- EM Microelectronics (EM4135)
- Fujitsu (MB89R116)
- Fujitsu (MB89R118)
- Fujitsu (MB89R119)
- Infineon (my-d page mode) 0x60
- Infineon (ISO address mode) 0xE0
- Infineon (My-d Light)
- NXP (I-Code SLI)
- NXP (I-Code SLI-S)
- NXP (I-Code SLI-L)
- STMicroelectronics (LRI512)
- STMicroelectronics (LRI64)
- STMicroelectronics (LRI2k, LRIS2k)
- Texas Instruments (Tag-it HFI Pro / Standard)
- Texas Instruments (Tag-it HFI Plus)
- Supported ISO15693 Host commands for non ISO15693 Transponders
- NXP I-Code UID Transponders
- NXP I-Code 1 Transponders
- Protocols for Buffered Read Mode and Notification Mode
- The Notification Mode Procedure
- Transponder Access in the Buffered Read Mode and Notification Mode
- x22] Read Buffer
- x31] Read Data Buffer Info
- x32] Clear Data Buffer
- x34] Force Notify Trigger
- ANNEX
- ANNEX B: Time Behavior of the Asynchronous Interface
- ANNEX C: Time Behavior of ISO15693 Host Commands
- Time Behaviour for [0x01] Inventory and ISO15693 Transponders
- ANNEX D: Index of Status Bytes
- ANNEX E: Codes of Reader Types
- ANNEX F: Examples for Read Data
- ANNEX F: Labeling of configuration parameter
Related products
OBID i-scan ID ISC.LRM2000OBID i-scan ID ISC.LR200 SeriesOBID i-scan ID ISC.MR200-EOBID i-scan ID ISC.MR200-WOBID i-scan ID ISC.MR200-AOBID i-scan ID ISC.MR200-EPIBID i-scan ID ISC.MR200OBID i-scan ID ISC.MR100-AOBID i-scan ID ISC.PR100-AOBID i-scan ID ISC.SPAD102Feig Electronic categories
Rfid Systems
Card Reader
Control Unit
Antenna
Other
Security Sensors
Controller
IP Access Controllers
Barcode Reader
Scanner
manualsdatabase
Your AI-powered manual search engine