manuals
database
Your AI-powered manual search engine
Search
Home
Brands
ABB
DC Drives
ACL30
ABB ACL30 User Manual
Print this manual
Download
ABB ACL30 User Manual
Table of content
Contents
List of related manuals
1. Safety instructions
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Contents of this chapter
General safety in installation, start-up and maintenance
Electrical safety in installation, start-up and maintenance
Additional instructions and notes
Grounding
General safety in operation
Intended audience
Terms and abbreviations
Installing and commissioning flowchart
Cyber security disclaimer
Operation principle
Layout
Control interfaces
Type designation label
Constructing the cabinet
Main dimensions and free space requirements
Cooling and degrees of protection
Preventing recirculation of hot air
Cabinet heaters
Unpacking
Checking the delivery
Installing the drive
Selecting the supply disconnecting device
Selecting the power cables
Typical power cable sizes
Alternative power cable types
Motor cable shield
Selecting the control cables
Routing the cables
Separate control cable ducts
Implementing thermal overload and short-circuit protection
Protecting the drive against ground faults
Protecting the contacts of relay outputs
Checking the insulation of the assembly
Break resistor assembly insulation
Connecting the power cables
Connection procedure
Installing power cable clamp plates
Power cable connection – frame size B
Power cable connection – frame sizes C and D (connector covers removed)
Connecting the control cables: JCU control unit
Jumpers
Safe Torque Off (X6)
The 7-segment display on the JCU control unit
Installing the optional modules
Start-up the drive
ACS-CP-U overview
Status line
Installing the control panel
Operating the control panel
Getting Help – Any mode
Finding panel version – any mode
Using basic operations – Any mode
Output mode
Setting speed reference in the Output mode
Using the Parameters option
Changing the value of value pointer parameters
Pointing the bit pointer parameter to a bit value in another signal
Changing bit pointer parameter value to 0 or 1
Changed Parameters mode
Editing changed parameters
Fault Logger option
Resetting faults
Time & Date option
Parameter Backup option
Backup and restore parameters
Handling parameter errors during backup and restore function
Restoring a user set between different firmware versions
Loading a user set between different firmware versions
Viewing backup information
I/O Settings
Reference Edit option
Drive Info option
Elevator system configuration
Local control vs. external control
Drive programming
Parameter restore
Basic start/stop operation
Drive faults
Elevator operation modes
Evacuation mode
Speed reference selection and scaling
Speed reference mode set to MULTIPLE
Speed reference mode set to SEP HIGH PRI or SEP LEVEL PRI
Speed reference scaling
Speed profile
Jerk selection
Smart slowdown
Mechanical brake control
Torque proving
Brake slip check
Operation time scheme
Inertia compensation
Protection functions
Motor stall
Leveling overtime stop
Programmable protection functions
Inputs and outputs
Digital inputs and outputs
Relay outputs
Autophasing for permanent magnet synchronous motors
Autophasing modes
Emergency stop
Encoder support
Absolute encoder configuration
Pulse encoder configuration
Rescue operation
Low voltage mode
Control through the embedded fieldbus interface: DCU 16-bit profile
Actual signals for the DCU 16-bit profile
Modbus register addresses for the DCU 16-bit profile
DCU 32-bit profile
Actual signals for the DCU 32-bit profile
Modbus register addresses for the DCU 32-bit profile
Setting parameters
Parameter groups 01...09
Parameter groups 10...99
How to reset
Fault messages generated by the drive
Heatsink
Cooling fan
Fan replacement (Frames C and D)
Other maintenance actions
Derating
Cyclic loads
Dimensions and weights
Supply cable fuses
AC input (supply) connection
Motor connection
Ambient conditions
Materials
CE marking
Compliance with EN 61800-3:2004
Second environment (drive of category C3)
U.S. patents
Selecting the mains choke
Connection diagram
Selecting EMC filters
JFI-0x (Frames B...D, category C2) installation
Selecting a brake resistor
Installing and wiring the resistor
Braking circuit commissioning
Frame size B
Frame size C
Frame size D
Mains chokes – CHK-0x
EMC filters – JFI-0x
EMC filter – JFI-0x dimensions
Brake resistors – JBR-xx
Brake resistors – JBR-xx dimensions
Product and service inquiries
ABB high performance elevator drives
User’s manual
ACL30 elevator drive
Next
/ 360
Zoom view
Related manuals for ABB ACL30
ABB ACS310 User Manual
ABB ACS880 User Manual
ABB ACH550 User Manual
ABB ACS310 User Manual
ABB ACS880 User Manual
ABB ACS355 User Manual
ABB ACS310 User Manual
ABB ACS880 User Manual
ABB ACS 160 User Manual
ABB ACS6080 User Manual
This manual is suitable for:
ACL30
manuals
database
Your AI-powered manual search engine
