ABB machinery drivesSupplementACS355 Solar pump inverter (+N827)

list of related manuals

About this chapter

Safety in installation and maintenance

Grounding

Control panels

I-V characteristics

Mechanical installation

Connection procedure

Installing control cables

Operating instructions

Viewing pump signals

Editing pump parameters

Boost voltage factor

Settings

Parameters

How to reset

Alarm messages

Inverter power rating

Fuse ratings

UL checklist

Product and service inquiries

ABB ACS355 Manual

List of related manuals

Introduction

Target audience

Contents of the manual

Cybersecurity disclaimer

Drive configuration

Configuring ACS355 drives

Starting ACS355 drives for PROFINET

ACS355 Minimum required parameter settings for PROFINET

ACS355 More parameters written from PLC to drive (optional)

ACS380 Minimum required parameter settings PROFIBUS DS

Starting ACS380 drives for PROFINET

ACS380 More parameters read from drive to PLC (optional)

Configuring ACS550 drives

Starting ACS550 drives for PROFINET

ACS550 More actual values or parameters to be read from drive to PLC (optional)

Configuring ACS580 drives

ACS580 Minimum required parameter settings for PROFIBUS DP

Starting ACS580 drives for PROFINET

ACS580 Minimum required parameter settings for PROFINET

ACS580 More parameters read from drive to PLC (optional)

ACS800 Minimum required parameter settings for PROFIBUS DP

Starting ACS800 drives for PROFINET

ACS800 Minimum required parameter settings for PROFINET

ACS800 More parameters read from drive to PLC (optional)

ACS850 Minimum required parameter settings for PROFIBUS DP

ACS850 Minimum required parameter settings for PROFINET

ACS850 More parameters read from drive to PLC

ACS880 Minimum required parameter settings for PROFIBUS DP

Starting ACS880 drives for PROFINET

ACS880 Minimum required parameter settings for PROFINET

ACS880 More parameters written from PLC to drive (optional)

ACSM1 Minimum required parameter settings for PROFIBUS DP

Starting ACSM1 drives for PROFINET

ACSM1 Minimum required parameter settings for PROFINET

ACSM1 More parameters read from drive to PLC (optional)

SIMATIC Manager

Setting PG/PC interface

Hardware configuration

Adding Rack and CPU to the hardware

Installing GSD files for ABB drives

Adding drives to PROFINET

Downloading Hardware configuration

PLC libraries for S7-300

Symbol Editor

FB500 ABB_DRIVE_CONTROL_FB

Block variables and data types

Setting the drive in standby mode

Setting the drive in run mode

Downloading a program and setting PLC in run mode

VAT table

FC501 ACS_DRIVE_PZD (optional)

Block variable and data types for FC501

Scalable variables and data types

FC500 ACS_DRIVE_PARA (optional)

TIA portal

Configuring S7-300 PLC

Installing GSD and GSDML file for S7-300 PLC

Adding ABB drives to PROFINET

Downloading configuration to PLC

Copying ABB drive libraries to S7-300 project

Adding PLC tags to S7-300

Adding watch and force tables

FC501 ACS_DRIVE_PZD

FC500 ACS_DRIVE_PARA

Error codes for FB500 and FC500

Configuring S7-1200 and S7-1500 PLC

Installing GSD file for S7-1200 PLC

PLC libraries for S7-1200

Downloading configuration to S7-1200 PLC

Copying ABB drive libraries to S7-1200 project

Adding PLC tags to S7-1200

Block variables and data types for FB500

FB501 ACS_DRIVE_PARA

Block variables and data types for FB501

FB502 ACS_DRIVE_PZD

Block variables and data types for FB502

Further information

Contact us

ACS355 series

Fieldbus grounding

Drives with embedded fieldbus

Fieldbus modules for ABB drives

ABB cable TK505

AC500 COM1 – Master at the bus line end

AC500‐eCo COM2 – Master at the bus line end

Drive configuration

Starting up ACS310 drives with embedded Modbus RTU

Starting up ACS355 drives with FMBA‐01 Modbus RTU adapter

Starting up ACS800 drives with RMBA‐01 Modbus RTU adapter

Starting up ACS850, ACQ810 drives with embedded Modbus RTU

Starting up ACS880 drives with FSCA‐01 Modbus RTU adapter

Starting up ACSM1 drives with FSCA‐01 Modbus RTU adapter

Install drives library

Control Builder Plus for PLC and Drives

IP configuration of CPU (for Ethernet connection between PC and PLC)

CODESYS

Library Manager

PLC logic

Download program to PLC

Create boot project

Test the program

Read and write more data between PLC and drive (optional)

Visualizations

Add more drives (optional)

Actualization rate

What this chapter contains

ACS355 drive configuration

Installing ABB Control Builder AC500

Configuring communication parameters

Checking the COM port of TK504

Getting help on a specific function block

Configuring the slave address of the drive

Copying the program for another drive

Creating a visualization for a copied drive program

Using visualizations

Configuring parameters to be read from the drive

Using the read parameters in the program

Program structure

DriveRef

Speed reference generation

ACS_DRIVES_CTRL_ENG

1. Safety

General safety

Contents of this manual

Quick installation and commissioning flowchart

Product overview

Power connections and control interfaces

Type designation label

Type designation key

Required tools

Unpacking

Installing

Fasten clamping plates

European union

Alternative power cable types

Additional US requirements

Relay cable

Control cable ducts

against thermal overload

Protecting the motor against thermal overload

Protecting the contacts of relay outputs

Motor and motor cable

Connecting the power cables

Connecting the control cables

Default I/O connection diagram

Checking the installation

How to start up the drive without a control panel

How to perform a manual start-up

How to perform a guided start-up

How to control the drive through the I/O interface

How to perform the ID run

Basic control panel

Overview

Operation

Output mode

Reference mode

Parameter mode

Copy mode

Basic control panel alarm codes

Assistant control panel

Parameters mode

Assistants mode

Changed parameters mode

Fault logger mode

Time and date mode

Parameter backup mode

I/O settings mode

Summary of the I/O connections of the application macros

ABB standard macro

wire macro

Alternate macro

Motor potentiometer macro

Hand/Auto macro

PID control macro