ACS850Quick Installation GuideACS850-04 Drive Modules (55…160 kW, 75…200 hp)English. . . . . . . . . . . . . . . . . . . . . 3中文 . . . . . . . . . . . . . . . . . . . . . . . 93ABD0000045488 Rev AEffective: 2012-01-20Based on:3AUA0000045488 Rev D 2012 ABB Oy. All rights reserved.

safety instructions

technical data

ABB ACS850 Quick Installation Manual

List of related manuals

Introduction

Target audience

Contents of the manual

Cybersecurity disclaimer

Drive configuration

Configuring ACS355 drives

Starting ACS355 drives for PROFINET

ACS355 Minimum required parameter settings for PROFINET

ACS355 More parameters written from PLC to drive (optional)

ACS380 Minimum required parameter settings PROFIBUS DS

Starting ACS380 drives for PROFINET

ACS380 More parameters read from drive to PLC (optional)

Configuring ACS550 drives

Starting ACS550 drives for PROFINET

ACS550 More actual values or parameters to be read from drive to PLC (optional)

Configuring ACS580 drives

ACS580 Minimum required parameter settings for PROFIBUS DP

Starting ACS580 drives for PROFINET

ACS580 Minimum required parameter settings for PROFINET

ACS580 More parameters read from drive to PLC (optional)

ACS800 Minimum required parameter settings for PROFIBUS DP

Starting ACS800 drives for PROFINET

ACS800 Minimum required parameter settings for PROFINET

ACS800 More parameters read from drive to PLC (optional)

ACS850 Minimum required parameter settings for PROFIBUS DP

ACS850 Minimum required parameter settings for PROFINET

ACS850 More parameters read from drive to PLC

ACS880 Minimum required parameter settings for PROFIBUS DP

Starting ACS880 drives for PROFINET

ACS880 Minimum required parameter settings for PROFINET

ACS880 More parameters written from PLC to drive (optional)

ACSM1 Minimum required parameter settings for PROFIBUS DP

Starting ACSM1 drives for PROFINET

ACSM1 Minimum required parameter settings for PROFINET

ACSM1 More parameters read from drive to PLC (optional)

SIMATIC Manager

Setting PG/PC interface

Hardware configuration

Adding Rack and CPU to the hardware

Installing GSD files for ABB drives

Adding drives to PROFINET

Downloading Hardware configuration

PLC libraries for S7-300

Symbol Editor

FB500 ABB_DRIVE_CONTROL_FB

Block variables and data types

Setting the drive in standby mode

Setting the drive in run mode

Downloading a program and setting PLC in run mode

VAT table

FC501 ACS_DRIVE_PZD (optional)

Block variable and data types for FC501

Scalable variables and data types

FC500 ACS_DRIVE_PARA (optional)

TIA portal

Configuring S7-300 PLC

Installing GSD and GSDML file for S7-300 PLC

Adding ABB drives to PROFINET

Downloading configuration to PLC

Copying ABB drive libraries to S7-300 project

Adding PLC tags to S7-300

Adding watch and force tables

FC501 ACS_DRIVE_PZD

FC500 ACS_DRIVE_PARA

Error codes for FB500 and FC500

Configuring S7-1200 and S7-1500 PLC

Installing GSD file for S7-1200 PLC

PLC libraries for S7-1200

Downloading configuration to S7-1200 PLC

Copying ABB drive libraries to S7-1200 project

Adding PLC tags to S7-1200

Block variables and data types for FB500

FB501 ACS_DRIVE_PARA

Block variables and data types for FB501

FB502 ACS_DRIVE_PZD

Block variables and data types for FB502

Further information

Contact us

ACS850 series

Fieldbus grounding

Drives with embedded fieldbus

Fieldbus modules for ABB drives

ABB cable TK505

AC500 COM1 – Master at the bus line end

AC500‐eCo COM2 – Master at the bus line end

Drive configuration

Starting up ACS310 drives with embedded Modbus RTU

Starting up ACS355 drives with FMBA‐01 Modbus RTU adapter

Starting up ACS800 drives with RMBA‐01 Modbus RTU adapter

Starting up ACS850, ACQ810 drives with embedded Modbus RTU

Starting up ACS880 drives with FSCA‐01 Modbus RTU adapter

Starting up ACSM1 drives with FSCA‐01 Modbus RTU adapter

Install drives library

Control Builder Plus for PLC and Drives

IP configuration of CPU (for Ethernet connection between PC and PLC)

CODESYS

Library Manager

PLC logic

Download program to PLC

Create boot project

Test the program

Read and write more data between PLC and drive (optional)

Visualizations

Add more drives (optional)

Actualization rate

What this chapter contains

Control Panel

Status line

Mounting the control panel on the cabinet door

List of tasks

Help and panel version – Any mode

Basic operations – Any mode

Output mode

How to set the speed, frequency, torque or position reference in the Output mode

Parameters

How to change the value of value pointer parameters

in another signal

How to change the value of bit pointer parameter to fixed 0 (FALSE) or 1 (TRUE)

How to select the monitored signals

Assistants

Changed Parameters

Fault Logger

How to reset faults

Time & Date

Parameter Backup

How to backup and restore parameters

How to view information about the backup

I/O Settings

Reference Edit

Drive Info

Parameter Change Log

English

Quick Start-up Guide for ACS850 with Standard Control Program

Dansk

Deutsch

HAUPTMENU

PAR GRUPPEN

Español

Italiano

Nederlands

Português (Brasil)

Svenska

Türkçe

Installation and maintenance work

Start-up and operation

Installation and commissioning flowchart

Terms and abbreviations

Motor control

Layout

Power connections and control interfaces

Type designation

Ordering information

Main dimensions and free space requirements

Cooling and degrees of protection

Preventing the recirculation of hot air

Contents of the package

Delivery check and drive module identification

Installation procedure

Mains choke installation

Other regions

Ground fault protection

Safe Torque Off

Selecting the power cables

Alternative power cable types

Considering the PELV requirements at sites above 2000 m (6562 ft)

Selecting the control cables

Control cable ducts

Electrical installation

Checking the insulation of the assembly

Power cable connection

Procedure

Grounding the motor cable shield at the motor end

Installation of power cable clamp plates

Power cable connection – frame size A

Power cable connection – frame size B

Power cable connection – frame sizes C and D (connector covers removed)

DC connection

Installation of optional modules

Connecting the control cables

Jumpers

DI6 (XDI:6) as a thermistor input

Drive-to-drive link (XD2D)

Grounding and routing the control cables

Checklist

Heatsink

Cooling fan

Fan replacement (Frames C and D)

Reforming the capacitors

Derating

Dimensions and weights

Supply cable fuses

AC input (supply) connection

JCU Control Unit

Efficiency


Contents safety instructions technical data	ACS850Quick Installation GuideACS850-04 Drive Modules (55…160 kW, 75…200 hp)English. . . . . . . . . . . . . . . . . . . . . 3中文 . . . . . . . . . . . . . . . . . . . . . . . 93ABD0000045488 Rev AEffective: 2012-01-20Based on:3AUA0000045488 Rev D 2012 ABB Oy. All rights reserved. Next / 16