ABB drivesSupplementFlange mounting kit installation

ABB ACS880-01 Installation Manual

ACH580-01 Series

Contents of this chapter

General safety in installation, start-up and maintenance

Electrical safety in installation, start-up and maintenance

Additional instructions and notes

Grounding

General safety in operation

Contents of this manual

Categorization by frame (size)

Quick installation and commissioning flowchart

Terms and abbreviations

Operation principle

Layout

Overview of power and control connections

External control connection terminals, frames R6...R9

Control panel

Control panel door mounting kits

Type designation key

Checking the installation site

Required tools

Unpacking and examining delivery, frames R1 and R2

Frames R1 and R2 cable box (IP21, UL Type 1)

Unpacking and examining delivery, frame R3

Unpacking and examining delivery, frame R4

Unpacking and examining delivery, frame R5

Frame R5 cable box (IP21, UL Type 1)

Unpacking and examining delivery, frames R6...R9

Frame R6 cable box (IP21, UL Type 1)

Frame R7 cable box (IP21, UL Type 1)

Frame R8 cable box (IP21, UL Type 1)

Frame R9 cable box (IP21, UL Type 1)

Installing the drive

Installing the drive vertically side by side

Flange mounting

European Union

Checking the compatibility of the motor and drive

Requirements table

Selecting the power cables

Power cable types

Additional guidelines, North America

Conductor type, IEC and North America

Typical power cable sizes, IEC

Typical power cable sizes, UL/NEC

Selecting the control cables, IEC and North America

Drive composer PC tool cable

Routing the cables

General guidelines, North America

Continuous motor cable shield or enclosure for equipment on the motor cable

Implementing short-circuit and thermal overload protection

Protecting the drive and the input power and motor cables against thermal overload

Implementing the Emergency stop function

Implementing the undervoltage control (power-loss ride-through)

Limiting relay output maximum voltages at high installation altitudes

Implementing a motor temperature sensor connection

Checking the insulation of the assembly

Brake resistor assembly for R1...R3

delta and TT systems

delta and midpoint-grounded delta systems

Guidelines for installing the drive to a TT system

Identifying different types of electrical power systems

Frames R1...R3

Frames R4...R9

Connecting the power cables

Connection procedure, frames R1...R4

Connection procedure, frame R5

Connection procedure, frames R6...R9

DC connection

Connecting the control cables

Default I/O connection diagram (HVAC default configuration)

Control cable connection procedure R1...R9

Installing option modules

Wiring the modules

Reinstalling grommets

Reinstalling covers

Reinstalling covers, frame R5

Reinstalling side plates and covers, frames R6...R9

Connecting a PC

When to connect EMC filter or disconnect ground-to-phase varistor: TN-S, IT, corner grounded delta and midpoint-grounded delta systems

Frames R1...R3, disconnecting EMC or varistor screws

Frames R4...R9, disconnecting EMC or varistor screws

Safety instructions

Related manuals

Frames R4 and R5: Removing the power clamp shelf and EMC shroud

cable box

Making holes into the UK gland plate

Installing the SWA glands

Installing the SWA gland over a power cable

Installing the SWA gland over a control cable

Attaching the UK gland plate to the drive – Frames R1 to R5

Attaching the UK gland plate to the drive – Frames R6 to R9

Installing the drive on wall – Frames R5 to R9

Obey the safety instructions

Select the power cables

Switch off the power and open the cover

Disconnect EMC filter or ground-to-phase varistor, if needed

Connect the power cables

Connect the control cables

Default I/O connections

Install optional modules, if any

Declaration of conformity

Check the insulation of the power cables and the motor

R6...R9 Figures E

Quick start-up guide

Before you start

Product and service inquiries

Introduction to the supplement

Main circuit diagram

Technical data

Installation

R1...R2

R3...R4

Auxiliary connector of the main switch (+B056+F278/F316)

Introduktion til supplementet

Driftsprincip

Hovedkredsløbsdiagram

Tekniske data

Overhold sikkerhedsinstruktionerne

Ekstra tilslutning for hovedafbryder (+B056+F278/F316)

Einführung in die Ergänzung

Funktionsprinzip

Hauptstromkreis-Schaltbild

Technische Daten

Befolgen Sie die Sicherheitsvorschriften

Hilfsanschluss des Hauptschalters (+B056+F278/F316)

Introducción al suplemento

Principio de funcionamiento

Diagrama del circuito principal

Datos técnicos

Siga estrictamente las instrucciones de seguridad

Instalación

Conector auxiliar del interruptor principal (+B056+F278/F316)

Johdanto

Toimintaperiaate

Pääpiirikaavio

Tekniset tiedot

EMC C1 -suodinta (+E223 ja +F316) käytettäessä

Noudata turvaohjeita

Asennus

Pääkytkimen lisäliitäntä (+B056+F278/F316)

À propos de ce supplément

Principe de fonctionnement

Étage de puissance

Caractéristiques techniques

Consignes de sécurité

Montage

Connecteur auxiliaire de l'interrupteur principal (+B056+F278/F316)

Introduzione al supplemento

Principio di funzionamento

Schema del circuito principale

Dati tecnici

Rispettare le norme di sicurezza

Installazione

Connettore ausiliario dell'interruttore principale (+B056+F278/F316)

Inleiding van het supplement

Werkingsprincipe

Hoofdcircuitdiagram

Technische gegevens

EMC klemmenblok (+E223 en +F316)

Volg de veiligheidsvoorschriften

Installatie

Hulpaansluiting van de hoofdschakelaar (+B056+F278/F316)

Wprowadzenie do dodatku

Podstawy obsługi

Schemat głównego obwodu

Dane techniczne

opcjonalnych z filtrem EMC C1 (+E223 i +F316)

Należy przestrzegać instrukcji bezpieczeństwa

Montaż

Dodatkowe złącze głównego rozłącznika (+B056+F278/F316)

Introdução ao suplemento

Princípio de operação

Diagrama do circuito principal

Dados técnicos

Cumpra as instruções de segurança

Instalação

Conector auxiliar do interruptor principal (+B056+F278/F316)

ACH580-31

ACQ580-01 Series

ACQ580-31 Series

ACS580-01 drives

ACS880-01 Series

ACS880-11

ACS880-31