AC International CT0-7TC-32 Instruction Manual
                       | |
WARRANTY43INSTRUCTION MANUALHARDWAREAED Electronics, Inc. warrants the original end user (“Customer”) that new Climatouch™ brandedproducts will be free from defects in workmanship and materials, under normal use, for two (2)years from the original purchase date.SOFTWAREAED Electronics, Inc. warrants to Customer that the Climatouch™ thermostat software will performin substantial conformance to its program specifications for a period of two (2) years from thedate of the original purchase.EXCLUSIONSThis warranty excludes (1) physical damage to the surface of the product, including cracks orscratches on the touch-screen or outside casing; (2) damage caused by misuse, neglect, improperinstallation, unauthorized attempts to open, repair, or modify the product, or any other causebeyond the range of intended use; (3) damage caused by accident, fire, power changes, otherhazard, or Acts of God; or (4) use of the product with any device if such device causes the problem.EXCLUSIVE REMEDIESShould a covered defect occur during the warranty period and Customer notifies AED Electronics,Inc., Customer’s sole and exclusive remedy will be, at AED Electronics, Inc.’s sole option andexpense, to repair or replace the product. Replacement products or parts may be new or recon-ditioned or a comparable version of the defective item. AED Electronics, Inc. warrants any replacedproduct or part for a period of ninety (90) days from shipment, or through the end of the originalwarranty, whichever is longer.OBTAINING WARRANTY SERVICECustomer must contact and return product to a local AED Electronics, Inc. product dealer orinstaller within the applicable warranty period to obtain warranty service. Dated proof of originalpurchase will be required. AED Electronics, Inc. will not be responsible for Customer’s memorydata contained in, stored on, or integrated with any products returned to AED Electronics, Inc.for repair, whether under warranty or not.WARRANTY EXCLUSIVETHE FORGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHERWARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESSFOR A PARTICULAR PURPOSE, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED BY AED Electronics, Inc. ANDITS SUPPLIERS..DISCLAIMERNEITHER AED Electronics, Inc. NOR ITS SUPPLIERS SHALL BE LIABLE FOR INCIDENTAL, CON-SEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FINANCIAL LOSSARISING OUT OF OR IN CONNECTION WITH THE SALE OR USE OF THIS PRODUCT, WHETHERBASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE) OR ANY OTHER THEORY, EVEN IF AEDElectronics, Inc. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AED Electronics,Inc.’S ENTIRE LIABILITY SHALL BE LIMITED TO REPLACEMENT OR REPAIR OF THE PRODUCT.IMPORTANT NOTICE42 Climatouch™ CT0-7TC-32>>WHEN USING THIS THERMOSTAT WITH A GAS FURNACE A COMMON WIRE (C)MUST BE CONNECTED.When working without a common wire:>>A confirm in HEAT MODE the cooling does not switch on or B confirm in COOLMODE the heat does not switch on.>>If test A or B fail or the thermostat shuts down in either HEAT or COOL MODEthen it is necessary to connect a common wire, (C), alternatively it may be possibleto solve this issue by simply connecting the 250 ohm 10 watt resistor between Cand W (in the case of a cooling problem - see B) or between C and Y1 (in the caseof a heating problem - see A) at the HVAC equipment.>>When working without a common wire, A confirm that when there is a call forheat, cooling does not also activate, and when there is a call for cool, heatingdoes not also activate.>>If using the configuration of Heat Pump and Furnace with no Common Wire confirmthat when Heat Pump and Furnace are working together (both stages are operatingat the same time) that the display does not go blank, if so you must use a CommonWire.>>This thermostat is equipped to run with two separated power transformers ifrequired RC and RH. Terminals RC and RH are internally connected together howeveryou should wish to use two transformers simply cut with a blade the copper trace onthe printed circuit board located between the C and Y2 screw terminals. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine