AC Pro GMV-ND07PLS/A-T(U) Installation Manual

Contents

AC Pro GMV-ND07PLS/A-T(U) Installation Manual Manual pdf 51 page image

465. Connect the drainage duct andscrew the new pump. Replace the motor with a new one.6. Install and screw the water tray. Use a screwdriver toscrew in the motor.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.9.3 Wall Mounted Type Indoor UnitMotor and FanPrecondition: The power supply has been disconnected.Step Diagram Operation Procedure1. Remove thelouver Take off the axle bush of the louver. Remove the louver.2. Open the frontpanelHold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.3. Remove the electrical boxcover 2 Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2. Detach the ambient temperaturesensor from the conduit.4. Remove the front panelassembly Unscrew the screws fixing the frontpanel assembly. Remove the front panel assembly.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.Multi Variable Air Conditioners Indoor Unit122Removal of Fan MotorStep Diagram Operation Procedure1．Remove thelouver●Take off the axle bush of the louver.●Remove the louver.2．Open the frontpanel●Hold the indents on both sides of thepanel and pull it out in the directionshown by the arrow.4. Remove thefront panelassembly●Unscrew the screws fixing the frontpanel assembly.●Remove the front panel assembly.5. Connect thedrainage duct andscrew the newpump.1. Screw the outlet pipe2. Screw the pump●Connect the drainage duct and usea screwdriver to screw the new pump.6. Install andscrew the watertray.Tighten the screws●Use a screwdriver to screw thewater tray.4.3 Wall Mounted Type Indoor UnitRemark: before removing, making sure power is disconnected.3. Remove theelectrical boxcover 2●Unscrew the screws fixing theelectrical box cover with a screwdriver.Take off the box cover 2.●Detach the ambient temperaturesensor from the conduit.