Abitana ABI-EV1012S00 Quick Start Manual
  |
110406_ABI-EV1012_QSG_ML.docEnglish Page 5 N.V. abitana S.A.ENGLISHABI-EV1012S00Twisted Pair BroadbandDistribution Amplifier with 2 RFinputs and IR-busQuick Start Guide1 Package Contents• DIN rail mountable Broadband Amplifier module• Quick Start Guide• 3 Termination plugs• Power jumper cord ABI-PS1001SPC2 Tools• Level tester ABI-TT1003S12• Spanner 11mm• Flat screw driver max. 5mm x 0.6mm3 IntroductionThe ABI-EV1012S00 is a Broadband Amplifier with two coaxialinputs (one for CATV signal or antenna, and the other for theconnection of a Broadband modulator)The unit has 4 independent RJ45 (Twisted Pair) outputs on thefront.A range of Twisted Pair to Coax adapters (with or withoutadjustment, filters, IR…) is available for installation at the receiverend (i.e. ABI-AC1001S00*).It is possible to connect a Radio by using a Radio adapter (ABI-AC1004S00) or an adaptor without a filter.4 ConnectorsP1 P2 P3POWERP4RF IN 1Input to CATV signa lor AntennaOutputs to 4 indepentTV SetsRF IN 1 Power AdjustmentRF IN 2Input toRF modulator outputIR-busIR-busGrounding wirePower level a djustmentConnection forIR DetectorABI-AC1007S005 PowerLoad ratio for this module = 0,5.Maximum allowed load ratio (sum of the load ratios for all modules) forpower supply ABI-PS1001S11 = 4.6 InstallationPower Off the central ABI-PS1001S11 Power Supply by means of theCircuit Breaker installed in the ‘Comm Center Cabinet’, or byremoving the mains power cord from the Power Supply.1. Make sure the shielding of the Network Interface Unit (NIU)or CATV transition point is properly connected to theprotective ground.2. Open the ‘Comm Center Cabinet’3. Click the ABI-EV1012S00 unit on the metal DIN-rail,adjacent to the ABI-EV1017S00 modulator (left or right side)for IR-bus functionality.4. The ABI-EV1012S00 is supplied with a grounding wire,connected to the input F-connector.This wire (1) must be connected to the protective ground ofthe installation.The following system devices also need to be connected tothe protective ground: The DIN-Rail frame (2) and the Powersupply (3)EV1002PowerSupplyDIN-Rail FramePE10021234DC1015ABI-PS1001SPC5. Provide power to the module using the included powerjumper cord ABI-PS1001SPC. Please consult the manual ofthe power supply for more information concerning theinstallation of the power supply.6. Connect a coax cable from the CATV connection point (NIU)or the CATV transition point to the coax connector on the topof the unit.7. Connect a coax cable (F-F patch cord) from the RF output ofthe ABI-EV1017S00 modulator to the coax connector (RF IN2) on top of the ABI-EV1012S00.Tighten the screws of the connector, using the spanner.Failing to follow the instructions (1) to (7) in the specified ordermay lead to permanent damage of the ABI-EV1012 amplifierWhen it is impossible to connect the DIN rails ,frame or CATVtransition point to ground, make sure they are at least at the sameelectrical level (connected to each other).Please also note our recommendation regarding overvoltage atthe end of this manual |
Related manuals for Abitana ABI-EV1012S00
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine