Accell UltraAV DisplayPort Setup Instructions
Also see for UltraAV DisplayPort: Setup instructions
Introduction:The Accell UltraAV DisplayPort to DisplayPort multi-monitor adapter allows you to connect up to three DisplayPort monitorsusing only one DisplayPort connector on your graphics card. Once connected, you have the freedom to configure themonitors as a single unified display (expanded mode), or three identical displays (clone mode) by simply changing theoutput resolution of your graphics card. This adapter is plug-and-play-ready, requiring no additional software or driver.Features:-Fully HD compatible supporting resolutions up to 3840x1024/60Hz/32bit color.-No additional software to install, just Plug-and-Play.-Works with any desktop or notebook computer (PC or Mac) that has a DisplayPort output.-Designed to work with monitors that have DisplayPort input, and it works best if the monitors are of the same nativeresolution, up to 1280x1024 per monitor.-If monitors are of different native resolutions, the adapter will display at a resolution common to the monitors.-If your graphics card has two DisplayPort ports, they can output to six monitors with two of these adapters!Specifications:• Connectors: Built-in 45” locking DisplayPort cable (to video card)• 3 DisplayPort outputs (to monitors) - DisplayPort cables not included• Max resolution: 3 monitors @1280x1024/60Hz/32bit color (3840x1024)*• Latency: Near zero**• Approximate dimensions: 6.5"(W) x 4"(L) x 1.5"(H)• Power: Bus-powered via video card• DisplayPort 1.1a compliant• Maximum supported monitor frequency: 60Hz*Recommended: Same type DisplayPort monitors used, having the same native resolution, not exceeding 60Hz refresh rate.**Features are subject to the capabilities of the computer and graphics card specification.Installation Overview:Follow the steps below to install the DisplayPort-to-3xDisplayPort adapter. It is recommended that monitors have the nativeresolution (up to 1280x1024) and refresh rate (up to 60 Hz).Clone Mode Installation Procedure:Expanded Mode Installation Procedure:UltraAV DisplayPort™ to DisplayPort™ Multi-MonitorAdapter - Set-Up InstructionsPackage Contents:• DP to 3x DP Monitors Adapter• InstructionsPC System Requirements:•DisplayPort video card and DisplayPortmonitors**•Microsoft® Windows® 7, Windows Vista™(32/64bit), Windows XP (32/64bit),Windows Server 2003/2008 (32/64bit),Windows 2000Macintosh System Requirements:•DisplayPort video card and DisplayPortmonitors** (note: mini DisplayPort video cardrequires Mini-DP to DP adapter - not included)•Mac® OS X v10.4, Mac OS X v10.5, Leopard(32/64bit)Step 1: Connect integrated DisplayPort(DP) input cable to desktop or notebookgraphics card connector.Step 2: Connect DisplayPort outputports 1, 2 and 3 to up to threemonitors respectively, according tothe monitors’ display sequence.Step 3: Select monitors’ inputport to DP1 . You will eithersee the same image on allmonitors (clone mode) or asingle image spread acrossmultiple monitors (expandedmode).Step 4: To change the display toclone mode, change the outputresolution on your computer andselect the horizontal resolutionequivalent to native resolution (orlower) for one (1) of the monitorsi.e. 1280x1080 (horizontal xvertical)Step 1: Connect integrated DisplayPort(DP) input cable to desktop or notebookgraphics card connector.Step 2: Connect DisplayPort outputports 1, 2 and 3 to up to threemonitors respectively, according tothe monitors’ display sequence.Step 3: Select monitors’ inputport to DP1 . You will eithersee the same image on allmonitors (clone mode) or asingle image spread acrossmultiple monitors (expandedmode).Step 4: To change the display toexpanded mode, change the outputresolution on your computer andselect the horizontal resolutionequivalent to three times the nativehorizontal resolution of one monitori.e. 3840x1080 (horizontal xvertical). |
Related manuals for Accell UltraAV DisplayPort
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine