Accustat Independence ES-AH11 Operating Instructions Manual
   |
Installation and Operating InstructionsES-AH11Specifications:Set Temperature Range: Determined by plug-in setpointPlug-in Setpoint Accuracy: ± 0.5°Control Accuracy: ± 1.0°Sampling Rate: Every 30 secondsSystem: Switch selectable, heat only, cool only or offStages: Single stage heating/coolingDifferential: Switch selectable, 0.5° or 1.0°Fan: Switch selectable, auto cycle or continuously onOperating Temperature: 14°F to 105°FStorage Temperature: -4°F to 105°FInput: 20VAC to 32VACLoad Rating: 1 amp maximum per circuit, 80mA minimum forenergy harvestingCycle Rate: 6 cycles per hourCommon Wire: OptionalDelay: 5 minutes on start-upEnergy Harvesting: Switch selectable, on or offEnable switch if not connecting a common wireDisable switch for sensitive loads, common wire will then be requiredThermostat Charge: Thermostat will hold its charge 3.5 hours duringa power failureEnclosure: High impact styrene, whiteCase can be locked, key required1Application:The ACCUSTAT® model ES-AH11 thermostat wasdesigned to operate 24VAC to 30VAC single stage heating and coolingsystems. This thermostat is MERCURY FREE!! The ACCUSTAT®models utilize pre-set plug-in temperature setpoints toactivate the circuits. Room air temperature is measured by a micro-processor and compared with the plug-in setpoint temperature. Thisthermostat can operate in heat only, cool only or be off. The fan cycleson/off with calls for heating or cooling or can be on continuously. Thethermostat has a locking cover to prevent tampering.Operating Conditions:The electronic mechanisms incorporated within this unit REQUIREoperating conditions similar to other electronic devices intended forINDOOR USE ONLY, such as would be acceptable for TV and similarhousehold appliances. Relative humidity must be less than 95% andthe atmosphere must be non-condensing. Air quality must be main-tained, FREE of heavy dust or debris which may infiltrate the interiorof this device. Installation in any space which is unfinished or under-going repainting or general rehabilitation is also considered productabuse. This device should be removed from service during any localconstruction activity.Cleaning:This device incorporates a high impact styrene enclosure which iseasily cleaned with a dry cloth or vacuum brush. Occasional soilingmay be cleaned with a soft cloth lightly dampened with water and/ormild cleaning solution. IN NO CASE should this device be directlysprayed with or exposed to free flowing liquids, including water, whichcould penetrate its interior.FAILURE TO OBSERVE ANY OF THE ABOVE CONDITIONS OF USEWILL COMPLETELY VOID THE SUPPLIER WARRANTY.CAUTIONMAKE SURE UNIT IS PROPERLY CONNECTED. DAMAGE TO THECONTROL CAN BE CAUSED BY MISWIRING, WHICH WILL VOIDTHE WARRANTY.TO OPEN:1. Align key with slot and insert all the way2. Locking pin will emerge. Pull out completely3. Gently squeeze left side of cover torelease catches4. Let right side work as a hingeSwing cover out and removeTO CLOSE: (Reverse Procedure)1. Hinge right side of cover and close it2. Gently squeeze left side of cover andsnap shut3. Orient the locking pin as shown andslide in until end is below surface ofcover (audible snap is heard whenpin is properly seated)1Insert3 4Squeeze2RemoveLift andRotateEnvironmentally FriendlyMERCURY FREE!!Use ONLY ACCUSTAT®Temperature SetpointsHEAT OFF COOLFANON AUTOACCUSTATATTENTION: This product does not contain mercury.This product may be replacing a product containingmercury.Do not place the old product in the household trash.For more information on recycling and proper disposalvisit TRC’s website www.thermostat-recycle.orgShould a tube break, do not touch any spilled mercury.Wear non-absorbent gloves, collect any spilled mercuryand place it in a sealed container. Contact your local wastemanagement authority for recycling and proper disposalinstructions. |
Related manuals for Accustat Independence ES-AH11
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine