Contents - Table Of Contents
- Table Of Contents
- Chapter 1 General Information
- Introduction
- Touch Screen (Optional)
- LCD Specifications
- Dimensions
- Chapter 2 System Setup
- A Quick Tour of the UTC-315
- Installation Procedures
- Running the BIOS Setup Program
- Installing System Software
- Installing the mSATA Card
- Installing the WLAN
- Jumpers and Connectors
- Locating Jumpers and Connectors
- Jumpers
- Table 4.5: JP4(D),JP5(EG),JP7(F):AT/ATX POWER SEL
- Table 4.8: JCASH1: CASH DRAWER POWER SEL
- Table A.1: CN1(DE),CN2(FG):Back Light
- Table A.3: CN4(DEFG):LVDS
- Table A.4: CN4(G):LVDS
- Table A.5: CN5(D),CN3(EF) eDP
- Table A.6: CN3(G) eDP
- Table A.7: CN11(DF),CN10(G) VGA
- Table A.9: CN7(D),CN3(EFG):SATA POWER
- Table A.11:CN9(D),CN6(EG),CN26(F):Touch
- Table A.15:MSATA1(DEFG):MSATA
- Table A.16:CN14(D),CN10(F),CN7(G):COM4
- Table A.17:CN15(D),CN12(F)CN11(G):COM3
- Table A.19:CN16(D),CN13(E),CN14(F),CN11(G):COM2
- Table A.21:CN21(D),CN16(EF),CN23(G):Power on switch
- Table A.24:CN23(D),CN17(EFG):LAN1/LAN2
- Table A.25:CN19(EF),CN21(G):External USB
- Table A.26:CN20(EF),CN22(G):External USB
- Table A.27:CN24,CN25 (D),CN18(EF),CN20(G):External USB
- Table A.28:CN26(D):External USB
- Table A.29:CN27(D),CN21(E),CN22(F),CN25(G):Line-out
- Table A.31:CN30(D),CN24(EF),CN27(G):HDMI
- Table A.32:CN31(DG),CN25(EF):DC-IN
- Table A.34:Power button
| 
UTC-315 User Manual 143.1 IntroductionThe UTC-315 consists of a PC-based computer that is housed in an plastic enclo-sure. You can install a HDD, DRAM, and MiniSATA card by removing the rear cover.Any maintenance or hardware upgrades can be easily completed after removing therear cover.3.2 Installing the 2.5" Hard Disk Drive (HDD)You can attach one Serial Advanced Technology Attachment (SATA) hard disk driveto the UTC-315's internal controller. The SATA controller supports faster data transferand allows the SATA hard drive to exceed 150 MB. The following are instructions forinstallation:1. Detach and remove the rear cover.2. Place the HDD in the metal bracket, and tighten the screws (see Figure 3.1).3. The HDD cable (SATA 7P+1*5P-2.5/SATA(15+7)P) is next to the metal brace.Connect the HDD cable to the motherboard (SATA1/SATA POWER). Plug theother end of the cable into the SATA hard drive.4. Put the rear cover on and tighten the screws.Figure 3.1 Installing primary 2.5" HDDWarning! Do not remove the rear cover until you have verified that no power isflowing within the UTC-315. Power must be switched off and the powercord must be unplugged. Every time you service the UTC-315, youshould be aware of this. |
