Banner MINI-BEAM Expert Series Quick Start Manual

Also see for MINI-BEAM Expert Series: Installation guide

Contents

Banner MINI-BEAM Expert Series Quick Start Manual Manual pdf 5 page image

SpecificationsSupply Voltage and Current10 V dc to 30 V dc (10% maximum ripple) at less than 45 mA,exclusive of loadSupply Protection CircuitryProtected against reverse polarity and transient voltagesAdjustmentsPush-button TEACH mode sensitivity setting; remote TEACH modeinput is providedIndicatorsTwo LEDs: amber and bi-color green/redConstructionReinforced thermoplastic polyester housing, totally encapsulated, o-ring seal, acrylic lenses, and stainless steel screws.Required Overcurrent ProtectionWARNING: Electrical connections must be made byqualified personnel in accordance with local andnational electrical codes and regulations.Overcurrent protection is required to be provided by end productapplication per the supplied table.Overcurrent protection may be provided with external fusing or viaCurrent Limiting, Class 2 Power Supply.Supply wiring leads < 24 AWG shall not be spliced.For additional product support, go to http://www.bannerengineering.com.Supply Wiring (AWG) Required Overcurrent Protection (Amps)20 5.022 3.024 2.026 1.028 0.830 0.5ConnectionsPVC-jacketed 5-conductor 2 m (6.5 ft) or 9 m (30 ft) unterminatedcable, or 5-pin Euro-style quick-disconnect (QD) fitting are available.QD cables are ordered separately.Application NotesThe first condition presented during TEACH mode becomes the outputON condition.Output ConfigurationBipolar: One current sourcing (PNP) and one current sinking (NPN)open-collector transistorOutput Rating150 mA maximum each output at 25° C, derated to 100 mA at 70° C(derate ≈1 mA per °C)Off-state leakage current: less than 5 μA at 30 V dcON-state saturation current: less than 1 V at 10 mA; less than 1.5 V at150 mAOutput Protection CircuitryProtected against false pulse on power-up and continuous overload orshort-circuit of outputsOutput Response TimeSensors will respond to either a “light” or a “dark” signal of 500microseconds or longer duration, 1 kHz max.NOTE: 1 second delay on power-up; outputs do notconduct during this time.Repeatability100 microseconds (all models)RatingMeets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67Operating ConditionsTemperature: –20° to +70° C (–4° to +158° F)Max. Relative Humidity: 90% at 50° C (non-condensing)TroubleshootingIf the MINI-BEAM Expert’s Power LED alternately flashes red/green, this indicates a microprocessor memory error. To clearthe error, re-teach the sensor or cycle the power ON and OFF and re-teach the sensor. If this does not solve the problem,or if it occurs frequently, replace the sensor.Banner Engineering Corp. Limited WarrantyBanner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warrantyperiod. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSEOF DEALING OR TRADE USAGE.This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BELIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHERARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any productpreviously manufactured by Banner Engineering Corp.Copyright NoticeAny misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as notintended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the productwarranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at anytime. For the most recent version of any documentation, refer to: www.bannerengineering.com. © Banner Engineering Corp. All rights reserved.MINI-BEAM Expert Serieswww.bannerengineering.com - Tel: +1-763-544-3164

/ 5

Related manuals for Banner MINI-BEAM Expert Series