Banner SSA-EB Series Instruction Manual

Banner SSA-EB Series Instruction Manual Manual pdf 1 page image

Instruction Manual30 mm Panel Mount Electro-Mechanical Push Buttons• Four styles of actuators: standard, illuminated, lockable, and illuminated lockable• Push-to-stop, twist-to-release (standard and lockable), or pull-to-release (standard)operation per IEC 60947-5-5• Latching design complies with ISO 13850; direct (positive) opening operation per EN60947-5-1• Compliant with ANSI B11.19, NFPA 79, and IEC/EN 60204-1 Emergency Stoprequirements• “Safe Break Action” ensures normally closed (NC) contacts will open if the contact blockis separated from the actuator• Panel mount though 30 mm mounting hole• "Emergency Stop" legend optionalModels SSA-EB… series are "mushroom-style" electro-mechanical emergency stop push buttons. These buttons mount through a30 mm hole in an enclosure. When the button is armed, the switch's safety contacts (normally closed/NC) are closed and itsmonitoring contacts (normally open/NO), if present, are open. When the button is pushed, the switch's safety contacts open, and themonitoring contacts close. The contacts remain in this condition until they are manual rearmed.The standard 40 mm and 60 mm actuators can be rearmed by pulling or twisting clockwise the red actuator. The lockable 44 mmactuator can be rearmed only by twisting the actuator clockwise. Do not pull the actuator while twisting or the switch may bedamaged, causing a malfunction or operational failure. The illuminated models provide a red indication within the face of the buttonthat allows for easy identification of a pushed/actuated button.SSA-EB1M… series padlock-style lockable emergency stop push buttons are intended to prevent unauthorized or accidentalresetting of a pushed/latched button. The SSA-EB1M… series are not to be used as an energy isolating device or as the sole meansof complying with Lockout/Tagout or with the requirements of the isolation of hazardous energy (see OSHA 29CFR1910.147, ANSIZ244.1, CSA Z460, ISO 14118). The locking feature can be used to provide supervisory/personal control and provide an additionalsafety measure(s) to reduce the likelihood of inadvertent arming and energization of the emergency stop circuit.ModelsTable 1: Non-illuminated modelsStandard 40 mm Standard 60 mm Lockable 44 mm Safety Contacts Monitor ContactsSSA-EB1P-02 SSA-EB2P-02 SSA-EB1MP-02 2 normally closed (NC)SSA-EB1P-04 SSA-EB2P-04 SSA-EB1MP-04 4 normally closed (NC)SSA-EB1P-11 SSA-EB2P-11 SSA-EB1MP-11 1 normally closed (NC) 1 normally open (NO)SSA-EB1P-13 SSA-EB2P-13 SSA-EB1MP-13 3 normally closed (NC) 1 normally open (NO)SSA-EB1P-22 SSA-EB2P-22 SSA-EB1MP-22 2 normally closed (NC) 2 normally open (NO)Table 2: Illuminated modelsStandard 40 mm Lockable 44 mm LED Safety Contacts Monitor ContactsSSA-EB1PL1-02 SSA-EB1ML1P-02 Per wiring connection 2 normally closed (NC)SSA-EB1PL1-04 SSA-EB1ML1P-04 Per wiring connection 4 normally closed (NC)SSA-EB1PL1-11 SSA-EB1ML1P-11 Per wiring connection 1 normally closed (NC) 1 normally open (NO)SSA-EB1PL1-13 SSA-EB1ML1P-13 Per wiring connection 3 normally closed (NC) 1 normally open (NO)SSA-EB1PL1-22 SSA-EB1ML1P-22 Per wiring connection 2 normally closed (NC) 2 normally open (NO)SSA-EB1PL2-12 SSA-EB1ML2P-12 PUSH ON 2 normally closed (NC) 1 normally open (NO)ISD Connect—All models with 2 normally closed (NC) contacts can be used with Banner's SSA-ISD-TCA by using anMQDMC-5xx(RA) series cable.Important... Read this before proceeding!The user is responsible for satisfying all local, state, and national laws, rules, codes, and regulations relating to the use of thisproduct and its application. Banner Engineering Corp. has made every effort to provide complete application, installation, operation,and maintenance instructions. Please contact a Banner Applications Engineer with any questions regarding this product.SSA-EB Series Emergency Stop Push ButtonOriginal Document194992 Rev. D21 September 2022194992