Bard T24H1 Installation Instructions Manual

Also see for T24H1: Installation instructions

Contents

Bard T24H1 Installation Instructions Manual Manual pdf 4 page image

Manual 2100-541DPage 4 of 28WALL MOUNT GENERAL INFORMATIONHEAT PUMP WALL MOUNT MODEL NOMENCLATURET 36 H 1 – A 10 X X X X X XNOTE: Vent options X, B and M are without exhaust capability. May require separate field supplied barometric relief in building.SHIPPING DAMAGEUpon receipt of equipment, the carton should bechecked for external signs of shipping damage. Ifdamage is found, the receiving party must contactthe last carrier immediately, preferably in writing,requesting inspection by the carrier’s agent.GENERALThe equipment covered in this manual is to be installedby trained, experienced service and installationtechnicians.The refrigerant system is completely assembled andcharged. All internal wiring is complete.The unit is designed for use with or without duct work.Flanges are provided for attaching the supply and returnducts.These instructions explain the recommended methodto install the air cooled self-contained unit and theelectrical wiring connections to the unit.These instructions and any instructions packaged withany separate equipment required to make up the entireair conditioning system should be carefully read beforebeginning the installation. Note particularly “StartingProcedure” and any tags and/or labels attached to theequipment.While these instructions are intended as a generalrecommended guide, they do not supersede anynational and/or local codes in any way. Authoritieshaving jurisdiction should be consulted before theinstallation is made. See Page 3 for information oncodes and standards.Size of unit for a proposed installation should bebased on heat loss/gain calculation made accordingto methods of Air Conditioning Contractors ofAmerica (ACCA). The air duct should be installedin accordance with the Standards of the NationalFire Protection Association for the Installation of AirConditioning and Ventilating Systems of Other ThanResidence Type, NFPA No. 90A, and Residence TypeWarm Air Heating and Air Conditioning Systems,NFPA No. 90B. Where local regulations are at avariance with instructions, installer should adhere tolocal codes.KW0Z - 0KW04 - 4KW05 - 5KW06 - 6KWF8 - 8KWS8 - 8KW09 - 9KW10 -10KW15 -15KW20 -20KW For 0 KW and circuit breakers (230/208 volt) or toggle disconnect (460V) applications, insert 0Z in the KW field of the model number. See Pages 24 & 25. Insert “D” for dehumidification with hot gas reheat. Reference Form 7960-627 for complete details.MODELNUMBER CONTROL MODULES(See Spec. Sheet S3436)VOLTS & PHASEA - 230/208/60/1B - 230/208/60/3C - 460/60/3REVISIONSVENTILATION OPTIONSX - Barometric Fresh Air Damper (Standard)B - Blank-off PlateM - Motorized Fresh Air DamperC - Commercial Ventilator - Mod. Spring Return w/ExhaustV - Commercial Ventilator - Spring Return w/ExhaustP - Commercial Ventilator - Power Return w/ExhaustE - Economizer (Internal) - Fully Modulating with ExhaustR - Energy Recovery Ventilator - Motorized with Exhaust(See Spec. Sheet S3398)COLOR OPTIONSX - Beige1 - White4 - Buckeye Gray5 - Desert Brown8 - Dark BronzeA - AluminumS - Stainless SteelCOIL OPTIONSX - Standard1 - Phenolic Coated Evaporator2 - Phenolic Coated Condenser3 - Phenolic Coated Evaporatorand CondenserOUTLET OPTIONSX - Front (Standard)H - Heat PumpCAPACITY |24 - 2 Ton30 - 2½ Ton36 - 3 Ton42 - 3½ Ton48 - 4 Ton60 - 5 TonFILTER OPTIONSX - 1-Inch Fiberglass (MERV 2)M - 2-Inch Pleated (MERV 11)H - 2-Inch Pleated (MERV 8)P - 2-Inch Pleated (MERV 6)E - 24V 1" Electrostatic Air CleanerSPECIALTY PRODUCTS (Non-Standard)