Beachcomber LEEP Owner's Manual
Also see for 321: Owner's guide
                     | |
Contents
| 
14 Beachcomber Hot Tub Owner’s Guide www.beachcomberhottubs.com 153. Time Display: You can change the time clock display fromthe 12 hour am/pm to a 24 hour time clock.ACCESSING THE USER EDIT MENUPress the then 1, then , USr will be displayed.Then press 1 to display Sr.n (Suppress reminders). Tosuppress press 1 again to make the n flash. Pressto change the n to a Y and then press 1 to confirm, thenbutton twice to exit. Reminders will now be removed.If you want to change the temp display from Fahrenheit to Cel-sius use the same procedure as above to get to Sr.n but thenpress to go to tc.n then 1 to make the n flash, tochange the n to Y and then 1 to confirm.If you want to change the time display from am/pm to 24 usethe same procedures as above to get to Sr.n and then presstwice to get to 24.n then press 1 to get the n to flash,press to change the n to Y and then 1 to confirmthen twice to exit.Start UpBefore turning on the power make sure you have read the Start Upinstructions on page 9. When your hot tub power is first turned onit will display a series of numbers identifying the software versionand the voltage input. It will then go into a 4 minute priming modeindicated by a Pr on the LCD display. During priming mode theHush Pump will circulate the water through the filter and heatingsystem to allow the temperature to be read. If your tub is not HushPump equipped the jet pump will not turn on until the prime modetimes out or the button is pressed to time out early. Duringprime mode the jet pumps can be turned on to make sure theyare fully primed and moving water in the tub. Do not allow anunprimed jet pump to run for more than 10 seconds. If the fill watertemperature is below 44°F / 7°C freeze protection will activateall pumps immediately. While the circulation pump is runningthe display will show a - - °F indicating current temperature is notknown. This will take two minutes. Once temperature is known itwill be displayed on the LCD.Temperature AdjustmentThe temperature range is 80°F - 104°F / 26°C – 40°C.The default is 100°F/37.5°C. Any temp changes are saved inthe system memory if power is interrupted. Use the button toincrease and the button to lower the set points. After showingset temp the LCD will revert back to current water temp.Note: if set temp is lowered more than 3°F / 1.5°C below currentwater temp the Hush Pump™ will stop. The circulation will restartevery 30 minutes to check if water temp has come down to settemp. It will also run continually during programmed times.Heating ModesTo change to the desired heating mode, press orfollowed by . Repeat these button presses to cycle through eachheating mode.There are 3 Heating Modes – Standard, Economy and SleepModes.Std – Standard Mode: (Default mode) In Standard Mode the wateris always heated to the set temperature. The display will show thecurrent temperature and the word STANDARD.Ecn – Economy Mode: In Economy Mode the water is heated onlyduring the filter cycle times. Default times are 8:00 am to 10:00am for cycle 1 and 8:00 pm to 10:00 pm for cycle 2. If usingeconomy you may need to alter these times to make sure the wateris at your desired temp during your usual tub use times. The displaywill alternate between Ecn and the current temperature anddisplay the word ECONOMY.SLP – Sleep Mode: In Sleep Mode the water is only heated towithin 20°F / 11°C of your set point and the heater only comeson during the programmed filter cycle times. This mode is typicallyonly used for vacation time. The display will alternate between thecurrent temperature and SLP.Massage 1To activate this jet pump press the 1 button once to activatelow speed, The icon will flash off and on, on the LCD display.Press again to activate high speed and the icon will becomesolid on the display. Press a third time to turn the pump off. The lowspeed will turn off automatically after 4 hours and the high speedwill turn off after 15 minutes.Note: If the hot tub is Hush Pump equipped, the low speed ofMassage 1 will come on automatically for 1 minute at the start ofeach filter cycle to purge the plumbing lines. If the purge time is notat the time of day you want, change the filter times.Massage 2To activate this jet pump press the 2 button once to activatelow speed, The icon will flash off and on, on the LCD display.Press again to activate high speed and the icon will becomesolid on the display. Press a third time to turn the pump off. Thelow speed and the high speed will turn off automatically after 15minutes.Note: If the hot tub is Hush Pump equipped, the low speed ofMassage 2 will come on automatically for 1 minute at the start ofeach filter cycle to purge the plumbing lines. If the purge time is notat the time of day you want, change the filter times.700 SeriesET-70 Topside Control Panel Operating InstructionsSHOCK HAZARD! NO USER SERVICEABLE PARTS.DO NOT ATTEMPT SERVICE OF THIS CONTROL. CONTACTYOUR RETAIL STORE OR SERVICE PROVIDER FOR ASSISTANCE.FOLLOW ALL OWNER’S GUIDE POWER CONNECTIONINSTRUCTIONS. INSTALLATION MUST BE PERFORMEDBY A LICENSED ELECTRICIAN AND ALL GROUNDINGCONNECTIONS MUST BE PROPERLY INSTALLED.ALWAYS TEST WATER TEMPERATURE PRIOR TO ENTRY USINGTHE TOPSIDE CONTROL PAD. ENSURE COMFORT BY ALSOCHECKING WATER WITH AN ACCURATE THERMOMETER.TAMPERING WITH OR MODIFYING THIS EQUIPMENT MAYVOID YOUR GUARANTEE.WARNING |
Related manuals for Beachcomber 321
manualsdatabase
Your AI-powered manual search engine