4-1Chapter 4LANVIEW LEDsThe front panel LANVIEW LEDs indicate the status of the module and may beused as an aid in troubleshooting. Shown in Figure 4-1 are the LANVIEW LEDs ofthe 9F206-02 module.Figure 4-1. 9F206-02 LANVIEW LEDsA19F206-02FDDISMB2CPUSMB and CPUFDDI Port Status

fcc notice

safety information

Features

Related Manuals

Unpacking the Module

User-Accessible Components

Setting the Module Card DIP Switch

Installing the Module into the MMAC-Plus Chassis

The Reset Switch

Flexible Network Bus (FNB)

System Management Bus

lanview leds

Safety

Physical

Cabletron Systems FDDI Repeater User Manual

frame relay module

about this manual

Network Example

Multiprotocol Support

Management Functions

Hardware Overview

WAN Port Cables for Netlink FRX4000

FRX6000

FRX6000 RLP, LICs, and Cables

LAN Card Interfaces

operator interfaces

Frame Relay Module

Frame Relay Module with I/O Boxes and Cabling

Introduction to Menu Operations

Moving Through the Menus

On-Line Help

Stopping Operation

Database Setup Recommendations

Producing a Configuration Report

Where to Find Database Records

Changing the Login Password

Setting the Date and Time

Configuring Node Defaults

Node Defaults Parameters

NetView Parameters

Warning Messages

FRX4000

LP Configuration Menu for FRX4000

FRX4000 Line Processor Parameters

LAN Interface

RLPs and Protocols

LP Configuration Menu for FRX6000

LP Parameters in an FRX6000

LAN Cards

LAN Card Configuration Screen

RLP and Protocols

Frame Relay Module RLP, LICs, and Cables

LP Configuration Menu for Frame Relay Module

LP Parameters in a Frame Relay Module

LAN Card Identification in FRX6000

LAN Card Parameters on FRM

Locations of Serial Ports

Physical Ports on FRX6000 RLP

Physical Ports on Frame Relay Module

Database and System Memory Values

Configuring a Physical Port

dlci sharing

Frame Relay Backup Examples

required configuration

Configuring Bandwidth Allocation Groups

Bandwidth Allocation Group Parameters

Configuring Frame Relay Ports

Frame Relay Port Screen 2

Frame Relay DLCI Configuration Screen 1

Frame Relay DLCI Configuration Screen 2

Frame Relay Port Parameters

Frame Relay DLCI Parameters

Configuring a Logical Port

Logical Port Parameters

Logical Port CUG Parameters

Configuring Subscriber Addresses

Subscriber Parameters

Configuring Frame Relay PVCs Across the Node

Frame Relay PVC Parameters

Configuring Frame Relay Backup Groups

Chapter 7 Configuring

Configuring X.25 Ports

X.25 Port Parameters

CUG Management

X.25 Port CUG Parameters

Configuring a Network Trunk

Configuring a Dial Port

Typical SVC Subscriber Screen

Configuring X.25 Address Translation Templates

Address Translation Templates Display

Translation Template Parameters

Translation Examples

Testing a Translation Template

Configuring X.25-to-X.25 PVCs

X.25 PVC Parameters

Configuring an SNA Port

SDLC PU Subscriber Parameters Screen

SNA Port Parameters

SNA Port PU Parameters

SVC Subscriber Parameters

Configuring a Hunt Group for SNA Subscribers

Configuring LLC2

MMAC-Plus 9F206-02

FDDI Repeater


Contents fcc notice safety information Table Of Contents Features Related Manuals Unpacking the Module User-Accessible Components Setting the Module Card DIP Switch Installing the Module into the MMAC-Plus Chassis The Reset Switch Flexible Network Bus (FNB) System Management Bus lanview leds Safety Physical	4-1Chapter 4LANVIEW LEDsThe front panel LANVIEW LEDs indicate the status of the module and may beused as an aid in troubleshooting. Shown in Figure 4-1 are the LANVIEW LEDs ofthe 9F206-02 module.Figure 4-1. 9F206-02 LANVIEW LEDsA19F206-02FDDISMB2CPUSMB and CPUFDDI Port Status Previous Next / 29