Caliber RG4D Installation Manual
Also see for CG36: User guide
1514All ranges must have an anti-tip device correctly installed as per the following instructions. If you pull therange out from the wall for any reason, make sure that the device is properly engaged when you pushthe range back against the wall. The bracket captures the post of the leveling leg to prevent tipping. If itis not, there is a risk of the range tipping over and causing injury if you or a child stand, sit or lean on anopen oven door.INCLUDED PARTS:4 #10 x 2” wood screws, (1) Anti-tip bracket, and (1) Installation Instructions.INSTALLING THE KIT:Instructions are provided for wood and cement floors. Any other type of construction may require specialinstallation techniques as deemed necessary to provide adequate fastening of the Anti-tip bracket to thefloor and wall. The use of this bracket does not preclude tipping of the range when not properly installed.Install the anti-tip bracket to the ground and wall 3 3/8” measuring from the left or right side edge ofthe range to the centerline of the bracket. The bracket engages the post of the leveling leg to preventtipping.WOOD CONSTRUCTION:Place the bracket against the back wall, into the right rear corner where the range is to be located. Leavea gap between the wall (or side of range} and the bracket 3 3/8” to the centerline of the bracket if thecabinet cut out matches the size of the range at 36” or 48” (see Fig. 5a and 5b on page 13). Drill (4) 1/8"diameter pilot holes in the center of the small holes. A nail or awl may be used if a drill is not available.Fasten the bracket securely to the floor and wall.For all installations:Fasten the bracket to the back wall using the four holes on the back of the bracket. Follow the methoddescribed in 'wood construction'.ModelSeriesRG3F-36, RG3G-36, RG3R-36& RG36-36RG4D-48, RG4F-48, RG4G-48,RG4R-48 & RG4T-48RG68BFTGD-72,RG66BF2GD-72“A” inFig. 5a& 5b onpage133 3/8” from right side edge ofthe range to the centerline ofbracket pictured, but can alsobe placed to 3 3/8” from theleft side edge of the range.WARNING!• A child or adult can tip the rangeand be killed.• Install the anti-tip device to thestructure.• Engage the anti-tip device.• Re-engage the anti-tip device ifthe range Is moved.• See Installation Instructions fordetails.Failure to do so can result in death orserious burns to children of adults.INSTALLATION ANTI-TIP DEVICE1. The range is a free standing unit. If the unit is to be placed adjacent to cabinets, theclearances shown in the following diagrams are required. The same clearances apply toisland installations.2. The range can be placed in various positions with respect to the cabinet front, with the frontframe either flush or projecting, depending on the countertop depth.3. The electrical and gas supply should be within the zones shown in the following diagrams.4. A manual shut-off valve {supplied by the installer) must be installed in an accessible locationin the gas line external to the appliance for the purpose of turning on or shutting off gas tothe appliance. (In Massachusetts such shut-off valves should be approved by the Board ofState Examiners of Plumbers & Gas Fitters.) The shut-off valve must be located within 6 feet(1.8 meters) of the appliance it serves.Important!Caliber Appliances recommends Installing the manual shut-off valve In a location readilyaccessible by the customer, so that gas to the appliance can be shut off in an emergencysituation. However, the appliance must not be modified in any way to accommodate suchplacement.5. The maximum depth of over head cabinets installed on either side of the hood is 13”.6. Any openings in the wall behind the range and in the floor under the range must be sealed.7. Always keep the appliance area clear and free from combustible materials, gasoline andother flammable vapors and liquids.8. Do not obstruct the flow of combustion and ventilation air to the unit.9. The horizontal surfaces of the rangetop trim must not be below countertop level.CABINET PREPARATION |
manualsdatabase
Your AI-powered manual search engine