Cambridge Audio AZUR 740 C Owner's Manual

Contents

Cambridge Audio AZUR 740 C Owner's Manual Manual pdf 8 page image

8Operating instructionsLoading and unloading discs1. Press the Standby/On switch.2. Press the Open/Close button.3. When the disc tray has opened fully, place a disc carefully in the traywith the label side facing up.4. To close the disc tray, press the Open/Close button again. When thetray, with a correctly loaded disc, is fully closed the disc will startturning automatically. After the CD player has read the disc it will beready to play. Pressing Play will also close the tray and start playingthe disc.5. The disc tray can be opened at any time by pressing the Open/Closebutton. Only remove the disc after the tray has fully opened.Note:- Do not put anything except a Compact Disc into the tray, foreign objectsmay damage the mechanism.- Do not force the tray by hand during the opening and closingoperations.- To avoid dirt and dust entering the mechanism, keep the disc trayclosed.- If the Compact Disc is seriously scratched or too dirty the player maynot be able to read it or play it.- Never load more than one disc into the disc tray at one time.Normal disc play1. Switch on your amplifier and set its input selector to the correctposition. Adjust the volume control to a minimum.2. Press the Standby/On switch.3. Press the Open/Close button to open the disc tray, and load a disc.4. Press the Open/Close button again to close the tray. The CD playerwill read the disc and enter Standby mode. Alternatively pressing Playwill close the tray and start playing the disc.5. Press the Play button. The disc will start playing from the beginningof the first track. When the last track has finished playing, the CDplayer will return to Standby mode.6. To stop the disc at any point press the Stop button. Pressing thePause button while the disc is playing will pause the disc. When thedisc is paused the display will flash, play can be resumed by pressingthe Play button again.Locating a specific track1. Ensure that a disc is loaded.2. Pressing the right Skip/Scan (Skip on remote) button once willforward the CD by one track. Repeat as necessary.3. Press Play. The disc will play to the end of the disc and then return toStandby mode.4. Pressing the left Skip/Scan (Skip on remote) button will access theprevious track.Locating a particular point in a track1. Ensure that the disc is playing the desired track.2. Press and hold the right Skip/Scan button (Search on remote), theCD will then fast forward within the track.3. Release the button when the desired time has been reached. Playwill resume.4. Press and hold the left Skip/Scan (Search on remote) button, the CDwill then rewind within the track.Repeating discs and tracks1. Ensure that the disc is playing.2. Press the Repeat button on the remote control. ‘Repeat All’ willappear on the display. The whole disc will now be repeated until thefunction is turned off.3. To repeat a specific track press Repeat twice while the track isplaying. ‘Repeat’ will appear on the display and the selected track willnow be repeated until the function is turned off.4. Press Repeat again to turn off the repeat function.Playing tracks in a random order1. Ensure that a disc is loaded and the player is in Standby mode.2. Press the Random button on the remote control. ‘Random’ willappear on the display.3. Press Play. The CD Player will now play the entire disc in a randomorder.4. Press Random to exit Random function. The disc will continue playingto the end in the correct order.5. Press the Stop button at any time to stop the disc.Using the Intro function1. Ensure that a disc is loaded. The player can be in Standby mode orplaying.2. Press Intro on the remote control. If the player is in Standby mode itwill automatically play the first ten seconds of each track and thenreturn to Standby mode. If a disc is being played when Intro ispressed the player will progress to the next track and play the first tenseconds of any remaining tracks.3. Press Intro again at any time to enter normal play mode.Using the A-B function1. Ensure that the disc is playing, press A-B on the remote control. Thiswill allow you to continuously repeat a specific section of a track.2. Press the Repeat button on the remote control at the beginning of thesection you want to loop. The A-B icon will be displayed and the playerwill memorise the time A-B was pressed.3. Press A-B again at the end of the section that you want to loop. Theplayer will now continuously repeat the selected section.4. Press A-B again to return to normal play mode.Using the Remain function1. Ensure that the disc is playing.2. Press the Remain button on the remote control once to display thetime remaining on the track playing.3. Press Remain a second time to show remaining number of tracksand total disc time remaining.4. Press Remain again to return to normal play mode.Using the Space function1. Ensure that a disc is loaded. The player can be in Standby mode orplaying.2. Press Space on the remote control. ‘Space’ will appear on the displayand a four second gap will be put between each track played.