SpecificationsAngle of view LensconstructionMinimumaperture Max. magnification and field of view Min. focusingdistanceFilter diameter Hood Max. diameter and length Weight CaseDiagonal Vertical HorizontalEF14mm f/2.8L USM 114° 81° 104° 10-14 22 0.10X/246 × 375 mm (9.7” × 14.8”) 0.25 m/0.82 ft. *1 <3> *2 77 × 89 mm (3.0” × 3.5”) 560 g/19.6 oz. LP1016EF20mm f/2.8 USM 94° 62° 84° 9-11 22 0.14X/176 × 264 mm (6.9” × 10.4”) 0.25 m/0.82 ft. 72 mm <1> EW-75II 77.5 × 70.6 mm (3.1” × 2.8”) 405 g/14.2 oz. LP1214EF24mm f/1.4L USM 84° 53° 74° 9-11 22 0.16X/150 × 227 mm (5.9” × 8.9”) 0.25 m/0.82 ft. 77 mm <1> EW-83DII 83.5 × 77.4 mm (3.3” × 3.1”) 550 g/19.4 oz. LP1214EF28mm f/1.8 USM 75° 46° 65° 9-10 22 0.18X/139 × 212 mm (5.5” × 8.3”) 0.25 m/0.82 ft. 58 mm <1> EW-63II 73.6 × 55.6 mm (2.9” × 2.2”) 310 g/10.9 oz. LP814EF35mm f/1.4L USM 63° 38° 54° 9-11 22 0.18X/136 × 206 mm (5.4” × 8.1”) 0.3 m/0.98 ft. 72 mm <1> EW-78C 79 × 86 mm (3.1” × 3.4”) 580 g/20.5 oz. LP1214EF50mm f/1.4 USM 46° 27° 40° 6-7 22 0.15X/164 × 249 mm (6.5” × 9.8”) 0.45 m/1.48 ft. 58 mm <2> ES-71II 73.8 × 50.5 mm (2.9” × 2.0”) 290 g/10.2 oz. LP1014EF85mm f/1.8 USM 28°30’ 16° 24° 7-9 22 0.13X/191 × 287 mm (7.5” × 11.3”) 0.85 m/2.79 ft. 58 mm <1> ET-65III 75 × 71.5 mm (3.0” × 2.8”) 425 g/14.9 oz. LP1014EF100mm f/2 USM 24° 14° 20° 6-8 22 0.14X/175 × 262 mm (6.9” × 10.3”) 0.9 m/2.95 ft. 58 mm <2> ET-65III 75 × 73.5 mm (3.0” × 2.9”) 460 g/16.1 oz. LP1014EF200mm f/2.8L USM 12° 7° 10° 7-9 32 0.16X/152 × 226 mm (6” × 8.9”) 1.5 m/4.92 ft. 72 mm <2> *2 83 × 136.2 mm (3.3” × 5.4”) 790 g/27.7 oz. LH-D18*1 Built-in gelatine filter holder *2 Built-inCT1-7538-004 © CANON INC. 2006 2006.9.1This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may cause undesired operation.Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could berequired to stop operation of the equipment.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Consult the dealer or an experienced radio/TV technician for help.This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled“Digital Apparatus”, ICES-003 of the Industry Canada.Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques (de la classe B) prescrites dans le Règlementsur le brouillage radioélectrique édicté par le ministère des Communications du Canada.8. HoodThe hood can keep unwanted light out of the lens, and alsoprotects the lens from rain, snow, and dust. Engage the hoodattachment tabs on the lens with the tabs on the hood andturn the hood in the direction of the arrow to secure it to thelens.[Bayonet type]EF20mm f/2.8 USM, EF28mm f/1.8 USM and EF50mmf/1.4 USM (sold separately), and EF24mm f/1.4L USM andEF35mm f/1.4L USM (supplied with the lens).To fit the hood on the EF20mm f/2.8 USM, EF24mm f/1.4LUSM, EF28mm f/1.8 USM or EF35mm f/1.4L USM, alignthe hood’s attachment position mark with the red dot on thefront of the lens, then turn the hood clockwise until the lens’sred dot is aligned with the hood’s stop position mark .When attaching or detaching the hood, grasp the base of thehood to turn it. To prevent deformation, do not grasp the rimof the hood to turn it.Though there is no red dot on the hood for the EF50mm f/1.4USM (ES-71II), the attachment procedure is the same.• Part of the picture may be blocked if the hood is notattached properly.• The hood can be reverse-mounted on the lens for storage.[Clip-on type]EF85mm f/1.8 USM, EF100mm f/2 USM (sold separately)Press the buttons on both sides of the hood to attach asillustrated .[Cut-in type]Fixed type EF14mm f/2.8L USMThe hood and lens are a single unit.Pull-out type EF200mm f/2.8L USMPull the hood out from the front of the lens to use .Q The lens length is measured from the mount surface to thefront end of the lens. Add 21.5 mm when including the lenscap and dust cap.Q The size and weight listed are for the lens only, except asindicated.Q Product specifications and appearance are subject tochange without notice.